manualshive.com logo in svg

Festo 548076, Repair Instructions, Page: 86 / 92

Share
Download
Festo 548076 Repair Instructions Download Page 86

86 / 92

Festo 7DHTGd_en

4.6 

Mounting the energy throughfeed

4.6.1 

Mounting of the pneumatic and electrical module

An electrical module is additionally mounted on the pneumatic module of the P4E4 / P4L12 versions.
In the event of a pneumatic module defect, contact the regional Festo contact (

 

www.festo.com

).

1.  Insert the centring sleeves into the holes in the housing of the pneumatic 

module.

2.  Push the air pipe assembly through the rotary indexing table.

The air connections of the pneumatic module are on the same side as the air 
connections of the rotary indexing table.

3.  Carefully position the housing of the pneumatic module on the rotary index-

ing table, at the same time, feed the centring sleeves into the holes in the 
rotary indexing table.

4.  Screw in socket head screws (4×) and tighten to appropriate tightening 

torque.

Size

Tightening torque

DHTG-…-A-P4

2.9 Nm ±20 %

DHTG-…-A-P4E4

2.9 Nm ±20 %

DHTG-…-A-P4L12

2.9 Nm ±20 %

5.  Mount rotary distributor 

 

Chapter 4.6.2 on page 86

.

4.6.2 

Mounting the rotary distributor, only DHTG-…-A-P4 / P4E4 / P4L12

Requirement

The pneumatic and the electrical module are mounted 

 

Chapter 4.6.1 on page 86

.

DHTG-65 / 90-A-P4 / P4E4 / P4L12

1.  If dismantled, screw grub screw into the plate until it stops.

Summary of Contents for 548076





























































































Reviews:

No comments