background image

 

 

 

1. Precautions   

1.1 General Safety Precautions 

The product provides a safe source of electrical energy when operated as intended and as designed. 

Potentially hazardous circumstances such as excessive heat or electrolyte mist may occur under 

improper operating conditions, damage, misuse and/or abuse. The following safety precautions and 

the warning messages described in this part must be observed. 

If any of the following precautions are not fully understood, or if you have any questions, contact us 

for guidance.   

Risks of explosion 

 

Do not subject the battery to strong impacts. 

 

Do not crush or puncture the battery. 

 

Do not dispose of the battery in a fire. 

Risks of fire 

 

Do not expose the battery o temperatures in excess of 60

 

Do not place the battery near a heat source such as a fireplace. 

 

Do not expose the battery to direct sunlight. 

 

Do not allow the battery connectors to touch conductive objects such as wires. 

Risks of electric shock 

 

Do not disassemble the battery.   

 

Do not touch the battery with wet hands. 

 

Do not expose the battery to moisture or liquids. 

 

Keep the battery away from children and animals.   

Risks of damage to the battery 

 

Do not allow the battery to come into contact with liquids. 

 

Do not subject the battery to high pressures. 

1.2 Installation Precautions   

Please be aware that a battery presents a risk of electrical shock including high short-circuit current. 

Follow all safety precautions while operating the batteries. 

 

Remove watches, rings, and other metallic accessories. 

 

Use tools with insulated handles in order to avoid inadvertent short circuits. 

 

Wear rubber gloves and safety boots. 

Summary of Contents for SSIF2P15S48100C

























































Reviews: