Ferroli 604 Instructions For Use, Installation And Maintenance Download

Page: 8 / 24

BS EN 1212:2005

Chemicals used for treatment of water intended for human consumption. Sodium polyphosphate

BS EN 13076:2003

Devices to prevent pollution by backflow of potable water. Unrestricted air gap. Family A. Type A

BS EN 13077:2008

Devices to prevent pollution by backflow of potable water. Air gap with non-circular overflow
(unrestricted). Family A. Type B

BS EN 13959:2004

Anti-pollution check valves. DN 6 to DN 250 inclusive Family E, type A, B, C, and D

BS EN 1567:1999

Building valves. Water pressure reducing valves and combination water reducing valves. Require-
ments and tests.

BS 6880-2:1988

Code of practice for low temperature hot water heating systems of output greater than 45 kW. Selec-
tion of equipment

BS 6644:2011

Specification for the installation and maintenance of gas-fired hot water boilers of rated inputs be-
tween 70 kW (net) and 1.8 MW (net) (2nd and 3rd family gases)

BS 5854:1980

Code of practice for flues and flue structures in buildings

BS 6880-1:1988

Code of practice for low temperature hot water heating systems of output greater than 45 kW. Funda-
mental and design considerations

BS 6880-2:1988

Selection of equipment

BS 6880-3:1988

Installation, commissioning and maintenance

BS EN 13384-1:2015

Chimneys. Thermal and fluid dynamic calculation methods. Chimneys serving one heating appliance

BS EN 13384-2:2015

Chimneys. Thermal and fluid dynamic calculation methods. Chimneys serving more than one heating
appliance

PD CEN/TR 1749:2014

European scheme for the classification of gas appliances according to the method of evacuation of
the combustion products (types)

BS 2879:1980

Specification for draining taps (screw-down pattern)

BS 7671:2008+A3:2015 Requirements for Electrical Installations. IET Wiring Regulations

IGE/UP/1

Soundness testing and purging of industrial and commercial gas installations

IGE/UP/2

Gas installation pipework, boosters and compressors on industrial and commercial premises

IGE/UP/10

Installation of gas appliances in industrial and commercial premises

Detailed recommendations are contained in the following Standards and Codes of Practice:

Summary of Contents for 604

























Search results

Summary of Contents for 604

Reviews:

Related manuals for 604

Brands by name

Popular brands

Ferroli 604, Instructions For Use, Installation And Maintenance

Search results

Summary of Contents for 604

Reviews:

Related manuals for 604

Brands by name

Popular brands