Ferris ISZKAV23/52 Operator'S Manual Download Page 10

Operating
the Zero Turn Rider

GENERAL OPERATING SAFETY

Before first time operation:

• Be sure to read all information in the Safety and

Operation sections before attempting to operate this
tractor and mower.

• Become familiar with all of the controls and how to

stop the unit.

• Drive in an open area without mowing to become

accustomed to the unit. 

CHECKS BEFORE STARTING

• Check that crankcase is filled to full mark on dipstick.

See the engine Operators Manual for instructions
and oil recommendations.

• Make sure all nuts, bolts, screws and pins are in

place and tight.

• Adjust the seat position, and make certain you can

reach all controls from operators position.

• Fill the fuel tanks with fresh fuel. Refer to engine

manual for fuel recommendations.

WARNING

Never allow passengers to ride on the unit.

Before leaving the operators position for any
reason, engage the parking brake, disengage the
PTO, stop the engine and remove the key.

To reduce fire hazard, keep the engine, tractor
and mower free of grass, leaves and excess
grease. Do not stop or park tractor over dry
leaves, grass or combustible materials.

Gasoline is highly flammable and must be
handled with care. Never fill the tank when the
engine is still hot from recent operation. Do not
allow open flame, smoking or matches in the
area. Avoid over-filling and wipe up any spills.

DANGER

OPERATING ON SLOPES 
CAN BE DANGEROUS

Never operate on slopes greater than 30 percent
(16.7°) which is a rise of three feet vertically in 10
feet horizontally.

Operate the unit at a slow ground speed when
driving onto slope. 

Use extra caution when operating on slopes with
rear-mounted grass catcher. Mow UP and DOWN
the slope, never across the face, use caution
when changing directions and DO NOT START
OR STOP ON SLOPE.

8

Figure 2.  Pre-start Checks

A.  Fuel Tank Filler Neck
B.  Crankcase Oil Fill

B

A

A

Summary of Contents for ISZKAV23/52
































Reviews: