manualshive.com logo in svg

Ferris 5901756, Operator'S Manual

Share
Download
Ferris 5901756 Operator'S Manual Download Page 30

Not for 

Reproduction

30

ferrismowers.com

34

Work Functions:

Callout

Function

Amperage

A

Battery Ignition

20 amp

B

Brake Switch

3 amp

C

Platter

10 amp

D

Shaker

10 amp

E

Headlight

5 amp

F

Kill

N/A

G

Platter

N/A

H

Shaker

N/A

Auxiliary Functions:

Note: 

The auxiliary functions are not included with the

machine. The machine is equipped with auxiliary fuses for

optional add-on functions. 

Callout

Function

Amperage

I

Auxiliary 1 Fuse

5 amp

J

Auxiliary 2 Fuse

5 amp 

K

Auxiliary 3 Fuse

5 amp 

L

Auxiliary 1 Relay

N/A

M

Auxiliary 2 Relay

N/A

N

Auxiliary 3 Relay

N/A

Starter / Engine / Pump:

Callout

Function

Amperage

O

Pump Relay

N/A

P

Pump

40 amp

Callout

Function

Amperage

Q

Spreader Motor

Controller

20 amp

Check/Fill Hydraulic Oil Level

Oil Type:

 Parker HT-1000 hydraulic oil or equivalent. 

This unit is equipped with one hydraulic oil tank. This

hydraulic oil tank provides oil to the two wheel motors and

the pump. The level of oil in the hydraulic oil tank must be

checked, and if necessary, filled.
 

35

1. Locate the hydraulic oil tank. The hydraulic oil tank is

located on the right side of the unit (A, Figure 35). 

2. Check the oil level when the unit is cold. The oil should be

up to the “FULL COLD” mark (B) on the hydraulic oil tank.

If the oil is below this level, proceed to step #3. 

3. Before removing the tank cap, make sure that the area

around the tank cap and fill neck of the tank is free of

dust, dirt, and other debris. Remove the tank cap.

4. Add oil up to the “FULL COLD” mark.
5. Install the tank cap.
6. After adding oil to the tank, it may be necessary to purge

air from the hydraulic system. To purge air from the

hydraulic system, simply drive the machine.  

Summary of Contents for 5901756









































Reviews:

No comments

Brands by name

Popular brands

Load more brands