background image

39

Troubleshooting

Rider Troubleshooting Continued.

PROBLEM

CAUSE

REMEDY

Engine runs, but rider will 

1.

Hydraulic dump valve(s)

1. Turn dump valve(s) clockwise to close.

not drive.

in “open” position.

Torque to 80-120 in.lbs. (9-13.5 N.m.)

2.

Belt is broken.

2. See Drive Belt Replacement.

3.

Drive belt slips.

3. See problem and cause below.

4.

Brake is not fully released.

4. See authorized service dealer

Hydraulic pump drive belt slips.

1.

Pulleys or belt greasy or oily.

1. Clean as required.

2.

Belt stretched or worn.

2. Replace belt.

Brake will not hold.

1.

Brake is incorrectly adjusted.

1. See Brake Adjustment.

2.

Brake caliper pads worn.

2. Replace with new brake pads.

Rider steers or handles poorly.

1.

Steering linkage is loose.

1. Check and tighten any loose connections.

2.

Improper tire inflation.

2. See Regular Maintenance Section.

TROUBLESHOOTING THE  MOWER

PROBLEM

CAUSE

REMEDY

Mower will not raise.

1.

Lift linkage not properly attached

1. See authorized service dealer for repair.

or damaged.

Engine stalls easily with

1.

Engine speed too slow.

1. Set to full throttle.

mower engaged.

2.

Ground speed too fast.

2. Decrease Ground Speed.

3.

Cutting height set too low.

3. Cut tall grass at maximum cutting

height during first pass.

4.

Discharge chute jamming 

4. Cut grass with discharge pointing toward

with cut grass.

previously cut area.

Excessive mower vibration.

1.

Blade mounting bolts 

1. Tighten to 70 ft.lbs. (94 N.m.).

are loose.

2.

Mower blades, spindles, 

2. Check and replace as necessary.

or pulleys are bent.

3.

Mower blades are out 

3. Remove, sharpen, and balance blades.

of balance.

See Maintenance Section.

4.

Belt installed incorrectly.

4. Reinstall Correctly.

Excessive belt wear or breakage.

1.

Bent or rough pulleys.

1. Repair or replace.

2.

Using incorrect belt.

2. Replace with correct belt.

Mower drive belt slips or fails to

1.

Idler pulley spring broken or not

1. Repair or replace as needed.

drive.

properly attached.

2.

Mower drive belt broken.

2. Replace drive belt.

Troubleshooting, Adjustment & Service

Summary of Contents for 5900621


























































Reviews: