background image

Not for 

Reproduction

35

Warranty Statement

BRIGGS & STRATTON WARRANTY POLICY (August 2021)

LIMITED WARRANTY

 

Briggs & Stratton warrants that, during the warranty period

specified below, it will repair or replace, free of charge, any

part that is defective in material or workmanship or both.

Transportation charges on product submitted for repair or

replacement under this warranty must be borne by purchaser.

This warranty is effective for and is subject to the time periods

and conditions stated below. For warranty service, find the

nearest Authorized Service Dealer in our dealer locator

map at 

 ferrismowers.com 

.The purchaser must contact

the Authorized Service Dealer, and then make the product

available to the Authorized Service Dealer for inspection and

testing. 

There is no other express warranty. Implied warranties,

including those of merchantability and fitness for a

particular purpose, are limited to the warranty period

listed below, or to the extent permitted by law . Liability

for incidental or consequential damages are excluded

to the extent exclusion is permitted by law.

 Some states

or countries do not allow limitations on how long an implied

warranty lasts, and some states or countries do not allow

the exclusion or limitation of incidental or consequential

damages, so the above limitation and exclusion may not

apply to you. This warranty gives you specific legal rights and

you may also have other rights which vary from state to state

or country to country.** 

WARRANTY PERIOD

Item

Consumer Use

Commercial Use

Equipment

3 years (36 months)

90 days (3 months)

Engine *

See Engine Operator's

Manual.

See Engine Operator's

Manual.

Battery (if equipped)

1 year (12 months)

1 year (12 months)

* Emissions-related components are covered by the

Emissions Warranty Statement 
** In Australia - Our goods come with guarantees that cannot

be excluded under the Australian Consumer Law. You are

entitled to a replacement or refund for a major failure and for

compensation for any other reasonably foreseeable loss or

damage. You are also entitled to have the goods repaired

or replaced if the goods fail to be of acceptable quality and

the failure does not amount to a major failure. For warranty

service, find the nearest Authorized Service Dealer in our

dealer locator map at 

 ferrismowers.com 

 (Select region:

Australia), or by calling 1300 274 447, or by emailing or

writing to [email protected], Briggs

& Stratton Australia Pty Ltd, 1 Moorebank Avenue, NSW,

Australia, 2170. 
The warranty period begins on the date of purchase by the

first retail or commercial customer. 
To ensure prompt and complete warranty coverage,

register your product at the website shown above or at

www.onlineproductregistration.com, or mail the completed

registration card (if provided), or call 1-800-743-4115 (in

USA). 
Save your proof of purchase receipt. If you do not provide

proof of the initial purchase date at the time warranty service

is requested, the manufacturing date of the product will be

used to determine the warranty period. Product registration is

not required to obtain warranty service on Briggs & Stratton

products. 

ABOUT YOUR WARRANTY

 

Warranty service is available only

through 

 Ferris® 

 Authorized Service Dealers. This warranty

only covers defects in materials or workmanship. It does not

cover damage caused by improper use or abuse, improper

maintenance or repair, normal wear and tear, or stale or

unapproved fuel. 

Improper Use and Abuse

 - The proper, intended use of

this product is described in the Operator's Manual. Using

the product in a way not described in the Operator's Manual

or using the product after it has been damaged will not be

covered under this warranty. Warranty coverage will also

not be provided if the serial number on the product has been

removed or the product has been altered or modified in any

way, or if the product has evidence of abuse such as impact

damage, or water/chemical corrosion damage. 

Improper Maintenance or Repair

 - This product must be

maintained according to the procedures and schedules

provided in the Operator's Manual, and serviced or repaired

using genuine Briggs & Stratton parts or equivalent. Damage

caused by lack of maintenance or use of non-original or non-

equivalent parts is not covered by warranty. 

Normal Wear and Tear

 - Like all mechanical devices, the

unit is subject to wear even when properly maintained. This

warranty does not cover replacement or repairs when normal

use has exhausted the life of a part or the equipment. Except

as noted in the warranty period, maintenance and wear items

such as filters, belts, cutting blades, and brake pads (except

engine brake pads) are not covered by warranty due to wear

characteristics alone, unless the cause is due to defects in

material or workmanship. 

Stale or Unapproved Fuel

 - In order to function correctly,

this product requires fresh fuel that conforms to the criteria

specified in the Operator's Manual. Engine or equipment

damage caused by stale fuel or the use of unapproved

fuels (such as E15 or E85 ethanol blends) is not covered by

warranty. 

Other Exclusions

 - This warranty excludes damage due

to accident, abuse, modifications, alterations, improper

servicing, freezing or chemical deterioration. Attachments

or accessories that were not originally packaged with the

product are also excluded. This warranty does not include

used, reconditioned, second-hand, or demonstration

equipment or engines. This warranty also excludes failures

due to acts of God and other force majeure events beyond

the manufacturer's control. 

80085753 Revision A

Summary of Contents for 500S Series





































Reviews: