background image

Cleaning and maintenance

22

Cleaning and maintenance

 

WARNING!

Risk of injury!

Accidentally starting the rotary hammer drill may result in severe injury.

 

− Always remove the mains plug from the socket before performing 

maintenance and cleaning.

 

WARNING!

Risk of electric shock!

Improperly handling the rotary hammer drill may result in severe injury.

 

− Before cleaning, pull the mains plug out of the socket.

 

− Make sure that no water or other liquids penetrate the inside of the rotary 

hammer drill.

Checking the rotary hammer drill

Check the condition of the rotary hammer drill regularly. Among other things, check to 

make sure:

 

− that the switches are not damaged,

 

− that the accessories are in proper condition,

 

− that the mains cord and the plug are not damaged,

 

− that the vents are unobstructed and clean. If applicable, use a soft brush to clean 

them.

After an operating time of approx. 5 hours, have a qualified professional open the 

gear grease filler hole 

8

 with the designated key 

13

 to ensure that there is 

enough grease. If necessary, have additional gear grease added to ensure that the 

device is adequately lubricated.

If you identify any damages, you must have them repaired by a specialist 

workshop to prevent risks.

Summary of Contents for FPB 1500































Reviews: