background image

17

Attachment and operation

Changing the grinding/sanding belt (6) (Fig. 6 - 9) 
•  Pull out the power plug
•  Remove the screws (18). 
•  Remove the grinding/sanding belt guard (19). 
•  Turn the grinding/sanding tensioner (10) to the right in order to reduce the tension on the 

grinding/sanding belt (6). 

•  Remove the grinding/sanding belt (6) to the rear.
•  Mount and the new grinding/sanding belt in reverse order. Important. Note the running 

direction: On the housing and on the inside of the grinding/ sanding belt!

Adjusting the grinding/sanding belt (6) 
•  Pull out the power plug
•  Push the grinding/sanding belt (6) by hand slowly in the running direction. 
•  The grinding/sanding belt (6) must run centrally on the grinding/sanding surface. If not, 

you can use the knurled screw (8) to make adjustments.

Moving the grinding/sanding position of the grinding/sanding belt (6) (Fig. 10-12) 
•  Loosen the Allen screw (5)  
•  Move the grinding/sanding belt (6) upwards into the desired position. 
•  Tighten the Allen screw (5) again to fix this position.  
•  In this position you can use the grinding/ sanding table to support the workpiece. To do this, 

first loosen the two allen screws (17) and then remove the stop rail (7). The grinding table 
can now be pushed into the hole in the holder tube (20) and fixed with the screw (1)

Replacing the abrasive paper on the grinding/sanding disk (11)
Dismantle the bottom wheel guard (15) by removing the 2 screws (16). Pull the sanding/ grind-
ing paper off the sanding/grinding disk (11) and attach the new sanding/grinding paper 
(quick-fit fastening system).

Mounting belt/disc sander to work bench 
If your belt/disc sander is to be used in a permanent location, it is recommended you secure it 
to a workbench or other stable surface.

•  Mark holes on workbench where belt/disc sander is to be mounted using holes in the base 

as a template for hole pattern.

•  Drill holes through workbench.

•  Place belt/disc sander on workbench aligning holes in the base with holes drilled in the 

workbench.

•  Insert bolts (not included) and tighten securely with lock washers and hex nuts (not 

included). Note: All bolts should be inserted from the top. Install the lock washers and hex 

nuts from the underside of the workbench.

Summary of Contents for BDG 915























Reviews: