10
EN
When device is not in use for 3 min, it will
automatically go in to sleep mode. While in sleep
mode the LED light can not be used.
The battery must be charged before first
use.
Removing the battery from the machine
Fig. B
•
Push the battery unlock button (3) and pull the
battery out of the machine.
Inserting the battery into the machine
Fig. B
Ensure that the exterior of the battery is
clean and dry before connecting to the
charger or machine.
• Insert the battery (2) into the base of the machine.
•
Push the battery toward the battery connector
until it clicks into place.
When the machine is not being used
over a longer period of time it is best to
store the battery in charged condition.
The appliance vibrates during operation.
During operation, always makes sure the
machines is placed on its rubber feet.
Switching on/ off the machine
•
Press the Pressure selector (21) and the
display (28) will go on.
•
The machine will automatically switch off
after a few miniutes or when battery is being
removed or hold the Pressure selector (21) for
a few second and the display (28) will go off.
HIGH PRESSURE, Low volume –
TYRES & BALLS - Switch ‘I’
Fig. D1, D2
Connecting the high pressure connection
valve without valve adapter
1.
Open the connection valve (8); the clamping
lever (7) will be in position as shown on figure D1.
2.
Insert the open connection valve (8) into
the valve of the inflatable (if necessary, first
remove valve cover of the inflatable).
3.
Hold the connection valve (8) and close: push
clamping lever (7) towards the connection
valve (8).
Connecting the high pressure connection
valve with valve adapter
Take care not to over-inflate footballs,
they might burst.
Given the material composition of
inflatable mattresses, inflatable boats
etc., the air pressure cannot be indicated
exactly. Take care therefore not to over-
inflate such items or they might burst.
For valve adapter for balls and the extra small
valve adapter for inflatables
1.
Open the connection valve (8); the clamping
lever (7) will be in position as shown on figure D1.
2.
Push or twist the respective valve adapter (14,
15) into the opening in the connection valve (8).
3.
Secure the valve adapter (14, 15) by closing
the connection valve (8): push clamping lever
(7) towards the connection valve (8) as shown
on figure D2.
4.
Insert the valve adapter (14, 15) into the valve
on the inflatable (if necessary, first remove
valve cover of the inflatable).
For valve adapter for tyres
1.
Turn the valve adapter (16, 17, 18) on to the
valve of the tyre (if necessary, first remove
valve cover of the tyre).
2.
Open the connection valve (8); the clamping
lever (7) will be in position as shown on figure D1.
3.
Push the connection valve (8) on the valve
adapter (16, 17, 18)
4.
Hold the connection valve (8): push clamping
lever (7) towards the connection valve (8) as
shown on figure D2.
Setting the Automatic Shut-Off Pressure
Fig. E
1.
Press the pressure selector (21) on the
controle panel to switch between the different
pressure Units ( PSI, BAR, Kpa) until required
unit is displayed.
2.
Press the “+”or “-“ on the controle panel until
the desired pressure shows on the display. By
holding the “+”or “-“ you can go up or down
quicker, release “+”or “-“at the dissured pressure.
NOTE:
After 3 seconds the display will flash and
return to a reading of “0.0”. This is normal.
Summary of Contents for CRM1054
