Ferm
109
Batteriladeren er dobbelt isoleret i overensstemmelse med EN 60335; der
kræves således ingen jording.
Udskiftning af ledninger eller stik
Gamle ledninger og stik skal smides væk, når de er blevet udskiftet med nye. Det er farligt
at sætte stikket på en løs ledning i en stikkontakt.
Isætning og udtagning af batteriet
Fig. B
Kontroller, at batteriet og maskinen er rene og tørre udvendig, før laderen slut-
tes til.
•
Sæt batteriet (5) i maskinens fod som vist på tegningen. Tryk på batteriet, indtil det
klikker på plads.
•
Tryk på låsepalerne på begge sider (10) før batteriet løsnes og tag det derefter ud af
maskinen.
Start og stop
Fig. 1
Håndtaget er designet med en frigøringsknap for at forhindre opstart ved et uheld.
•
Tryk og hold på frigøringsknappen (3), placeret på begge sider af håndtaget, tryk
herefter på hovedkontakten (4)
•
Frigør hovedkontakten for at stoppe bladene.
Vælg det blad, der skal bruges
•
Det lille græsklipper blad er bedst til at klippe græs omkring træer og andre faste ting
i haven. Kan også bruges til planteskulpturer.
•
Det store hækketrimmer blad er bedst til egentlige hække og buske.
Udskiftning af blad
Fig. C
Fjern det genopladelige batteri, før klingerne udskiftes.
Fare for personskade! Bær beskyttelseshandsker!
3. BETJENING
08
Ferm
use tool in conjunction with a residual circuit breaker device.
3) Personal
safety
a. Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the influence of drugs, alco-
hol or medication. A moment of inattention while operating power tools may result in
serious personal injury.
b. Use safety equipment. Always wear eye protection. Safety equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate con-
ditions will reduce personal injuries.
c. Avoid accidental starting. Ensure the switch is in the off position before plugging in.
Carrying power tools with your finger on the switch or plugging in power tools that
have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a
key left attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
f.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in
moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of these devices can reduce dust
related hazards.
h.
Use clamps or a vice to hold work. It’s safer than using your hand and it frees both
hands to operate tool.
4)
Power tool use and care
a.
Do not force the power tool. Use the correct power tool for your application. The cor-
rect power tool will do the job better and safer at the rate for which it was designed.
b.
Do not use the power tool if the switch does not turn it on and off. Any power tool
that cannot be controlled with the switch is dangerous and must be repaired.
c.
Disconnect the plug from the power source before making any adjustments, chan-
ging accessories, or storing power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d.
Store idle power tools out of the reach of children and do not allow persons unfamili-
ar with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e.
Maintain power tools. Check for misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the power tools operation. If dama-
ged, have the power tool repaired before use. Many accidents are caused by poorly
maintained power tools.
f.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cut-
ting edges are less likely to bind and are easier to control.
g.
Use the power tool, accessories and tool bits etc., in accordance with these instructi-
ons and in the manner intended for the particular type of power tool, taking into
account the working conditions and the work to be performed. Use of the power tool
for operations different from intended could result in hazardous situation.
h.
Damaged switches must be replaced at a customer service repair centre. Do not use
GB
D
NL
F
E
P
I
S
FIN
N
DK
