JAM PROOF SYSTEM OPERATION*
*100% Jam Proof when used in accordance with user manual
Advanced Jam Prevention- Electronically
measures paper thickness to prevent paper jams:
Remove several sheets until
indicator is below red.
Continue 100% Jam
Proof Shredding
If a misfeed
occurs:
If
illuminates after paper has been
reversed, press reverse and remove paper.
Otherwise, regular shredding will resume.
1
2
3
Up to RED: Too many
sheets have been inserted.
Up to GREEN: More sheets
can be added.
Up to YELLOW: Productivity
is optimized.
All indicators light up and
shredder pauses for 3-6 seconds
Wait for flashing to stop after automatic correction
is complete. Regular shredding will resume.
2
Press ( )ON to
activate (blue)
PAPER OR CD/CARD
BASIC SHREDDING OPERATION
1
Feed paper straight into
paper entry and release
3
Plug in and put
disconnect power
switch in ON (I) position
Continuous operation:
10-minute maximum
NOTE:
Shredder runs briefly
after each pass to clear entry.
Continuous operation beyond
10-minutes will trigger
20-minute cool down period.
3
ADVANCED PRODUCT FEATURES
Eliminates paper jams and powers through tough jobs.
Jam Proof System
Eliminates paper jams and powers
through tough jobs.
Patented SafeSense
®
Technology
Stops shredding immediately when
hands touch the paper opening
Energy Saving System
Optimal energy efficiency
100% of the time – in use
and out of use.
SafeSense
®
is active and
working properly
Touch test area and
look for the SafeSense
®
indicator to illuminate
Turn the shredder ON
( ) to activate SafeSense
®
SAFESENSE
®
TECHNOLOGY
SET-UP AND TESTING
Stops shredding immediately when hands
touch the paper opening.
WHEN IN SLEEP MODE
In sleep mode
To get out of sleep mode
touch control panel
insert paper
2
3
1
or
1
3
2
ENERGY SAVING SYSTEM
• Saves energy in four ways: energy-efficient electronics, jam prevention, standby mode and
sleep mode.
• Sleep Mode shuts down shredder after 2 minutes of inactivity.
Optimal energy efficiency 100% of the
time – in use and out of use.
4
When finished
shredding set
to OFF ( )
5
or
Hold CD/card at edge,
feed right side of entry
and release
For more information about all of Fellowes Advanced Product Features go to
www.fellowes.com
4
ENGLISH
Model 73Ci
PRODUCT MAINTENANCE
TROUBLESHOOTING
TO CLEAN THE SENSORS
CLEANING AUTO-START INFRARED SENSORS
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors
may become blocked by paper dust causing the motor to run even if there is no paper present.
(Note: two paper detection sensors are located in the center of the paper entry)
.
All cross-cut shredders require oil for peak performance. If not oiled, a
machine may experience diminished sheet capacity, intrusive noise when
shredding, and could ultimately stop running. To avoid these problems, we
recommend you oil your shredder each time you empty your waste bin.
OILING SHREDDER
15
15
* Only use a non-aerosol vegetable oil in long
nozzle container such as Fellowes 35250
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
Turn off and unplug
shredder
Locate Auto-start
infared sensor
Using cotton swab, wipe
away any contamination
from the paper sensors
Dip cotton swab in
rubbing alcohol
Press and hold forward
( ) 2-3 seconds
*Apply oil across entry
3
1
2
4
1
2
Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This
indicator will remain illuminated and the shredder will not operate for the duration of the recovery time. See Basic Shredding Operation for more information about
the continuous operation and recovery time for this shredder.
Bin Full: When illuminated, the shredder waste bin is full and needs to be emptied. Use Fellowes waste bag 36052.
Bin Open: The shredder will not run if the bin is open. When illuminated, close the bin to resume shredding.
Remove Paper: When illuminated, press reverse ( ) and remove paper. Reduce paper quantity to an acceptable amount and refeed into paper entry.
SafeSense
®
Indicator: If hands are too close to the paper entry, the SafeSense
®
indicator will illuminate and the shredder will stop shredding. If SafeSense
®
is active for 3 seconds, the shredder will automatically turn off and the user must press the power button on the control panel to resume shredding.
LIMITED PRODUCT WARRANTY
Limited Warranty: Fellowes, Inc. (“Fellowes”) warrants the parts of the machine to be free of defects in
material and workmanship and provides service and support for 1 year from the date of purchase by the
original consumer. Fellowes warrants the cutting blades of the machine to be free from defects in material
and workmanship for 1 year from the date of purchase by the original consumer. If any part is found to
be defective during the warranty period, your sole and exclusive remedy will be repair or replacement,
at Fellowes’ option and expense, of the defective part. This warranty does not apply in cases of abuse,
mishandling, failure to comply with product usage standards, shredder operation using an improper power
supply (other than listed on the label), or unauthorized repair. Fellowes reserves the right to charge the
consumers for any additional costs incurred by Fellowes to provide parts or services outside of the country
where the shredder is initially sold by an authorized reseller. ANY IMPLIED WARRANTY, INCLUDING THAT
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO
THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable for any
consequential or incidental damages attributable to this product. This warranty gives you specific legal rights.
The duration, terms, and conditions of this warranty are valid worldwide, except where different limitations,
restrictions, or conditions may be required by local law. For more details or to obtain service under this
warranty, please contact us or your dealer.
Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers.
Summary of Contents for POWERSHRED 73Ci
Page 2: ......
