background image

TROUBLESHOOTING TIPS CONNECTING TO WI-FI 

If you are having difficulty connecting:

•  Make sure the Wi-Fi network is a 2.4 GHz network.  

  Smart Strip Light will not connect to a 5 GHz network.

•  Test your Wi-Fi network with other devices such as your    

  phone to make sure it is operating properly. 

•  The Wi-Fi connection may not have good coverage  

 

  during set up. Try moving the Smart Strip Light closer  

 

  to your Wi-Fi router. 

For more information, check the App User Guide and visit 

www.feit.com/help

   

Download the Feit Electric app 

on your smart device

Prepare the Strip Light

Connect the Controller Module

Feit Electric app

Mount the Strip Light

Getting Started:

Peel adhesive tape from back of Strip Light to position 
and align strip light on mounting surface.
Screw in mounting clips (required for all long term 
installations). Save two clips to use for installing the 
Controller Module (Step 4).

Need Help?

FOR DETAILED INSTRUCTIONS ON SMART FEATURES SEE THE APP USER GUIDE.

WARNING:

 

These products may represent a possible shock or fire hazard if improperly 
installed or attached in any way. Products should be installed in accordance 
with this install guide, current electrical codes and/or the current National 
Electric Code (NEC).

Once cut, the portion of the strip light that will not connect to the controller 

can be disposed of in accordance with local recycling or waste regulations.

-  Measure the desired length before installation.
-  Clean the mounting area thoroughly (surface  

 

  must be free of dust, dirt or grease).
-  Avoid bending the strip light which may

  damage the LEDs.
-  Avoid removing and relaying the Strip Light

  multiple times as the adhesive may wear off.

Unroll strip light and place near mounting location. 
Ensure power supply and controller can reach to the 
start of the strip light. Do not connect to power yet.

(Optional) Connect to Google Assistant

or Alexa using the in App guide

Choose 

Alexa

 or Google Assistant

Tap 

••• menu icon

6

mounting clip

mounting 

clip

To activate smart features proceed to steps 5 & 6. 

When in Smart Wi-Fi pairing mode, the strip light will 

blink. Note: The unit will stop blinking after 3 minutes 

or when controlled with the RF remote.

You are now ready to use the Strip Light via RF Remote 

Controller. See “RF Remote Control” section for details. 

For 24/7 customer support,

visit 

feit.com/help

90˚ Max

Do not bend at LED

90˚ Max

Turn on Bluetooth and open the

Feit Electric app to complete the set up.

5

Be sure to connect to a 2.4 GHz 

Wi-Fi network that covers your 

installation location.

Tap 

Add Device or the + sign.  The device name(s) 

will pop up on the Feit app. Tap on 

Go to add

then select the device to add.

You will be prompted to enter 
your Wi-Fi network name and 
password.

Only one device may be added at 
a time using Bluetooth set up.  
Repeat Step 5 to add additional 
devices. Alternative set up options 
and help instructions are available 
in the Feit Electric app.

Connect the Strip Light to the controller module then 
connect the plug as shown in the image below. 
 

Connect power supply to wall outlet.
When using outdoors, plug the unit 
into an outdoor rated GFCI receptacle 
with appropriate outdoor cover.

•••

Use provided double-sided tape to adhere 

the back of Controller Module to mounting 

surface. Use mounting clips on both sides 

as shown above.

This strip light uses permanent tape and may cause surface damage 

if removed. Not recommended for mounting on brick or concrete.

Feit Electric is not responsible for damage to mounted surfaces.

Ensure the power supply is not plugged 
in at the wall outlet when mounting 
or cutting. 

Cut to length ONLY on the line or solder 

pads NEXT to the scissor markings on 

strip light, where the copper or silver 

metal is visible. Cutting at any other 
area will permanently damage the strip.

Optional - Add another Feit Electric Smart LED Strip Light 
(sold separately) to extend up to 32 feet.

SILVER

CONNECTION

COPPER

CONNECTION

CUT HERE

CUT HERE

Apply tape to back 

of male connector

If you are connecting two strip lights, use the included foam tape

to secure male connector to mounting surface.

FOAM TAPE

Reviews: