Top View
Adjust flood lights side to side
Adjust camera side to side
Adjust flood light carousel
side to side
Adjust flood lights and camera
up and down
Bottom View
Top View
Side View
FEIT ELECTRIC COMPANY
| PICO RIVERA, CA, USA | (800) 543-3348 | FAX (562) 908-6360 | www.feit.com
FEIT ELECTRIC COMPANY
| PICO RIVERA, CA, USA | (800) 543-3348 | FAX (562) 908-6360 | www.feit.com
WARNING:
This product may represent a possible shock or fire
hazard if improperly installed or attached in any
way. Product should be installed in accordance
with the owner’s manual, current electrical codes
and/or the current National Electric Code (NEC).
RISK OF ELECTRIC SHOCK:
TURN OFF THE MAIN POWER AT
THE CIRCUIT BREAKER BEFORE INSTALLING.
(12)(13)
(11)
(6)
(10)
(8)
(3)
(2)
(1)
EXTERNAL J-BOX INSTALLATION
PRE-INSTALLATION
Remove the Mounting Plate
(6) by unscrewing and
removing the Decorative Nuts
(13) and Rubber Washers (12).
L
GND
N
DETAIL
(12)
(11)
(13)
(8)
(10)
(12)
(11)
(13)
(8)
(10)
(4)
FLUSH J-BOX INSTALLATION
L
GND
N
DETAIL
1. J-Box (not included)
2. Mounting Bar
3. J-Box Screws (2 pieces)
4. Spacers (2 pieces)
5. Mounting Gasket
6. Mounting Plate
7. Terminal Block
8. Mounting Plate Screws (2 pieces)
9. Mounting Bar Screw (1 piece)
10. Fixture Body
11. Mounting Holes
12. Rubber Washers (2 pieces)
13. Decorative Nuts (2 pieces)
14. LED Flood Lights
15. Camera Lens and Photocell Sensor
16. Speaker
17. Motion Sensor
18. Mic
19. Indicator Light
(16)
(12)
(17)
(13)
(11)
(9)
(6)
(18)
(8)
(10)
(14)
(3)
(2)
(1)
(15)
(19)
(7)
(5)
(4)
TOOLS REQUIRED
(not included)
SEALANT
(6)
(5)
L
GN
D
N
(6)
(2)
(5)
(6)
(6)
(6)
(6)
(9)
L
GND
N
(4)
(7)
(7)
microSD CARD
INCLUDES 2 EXTRA SCREWS
RESET
BUTTON
(3)
(2)
(1)
(4)
(6)
(5)
(9)
L
GND
N
(4)
(2)
(6)
(5)
L
GN
D
N
(4)
RESETTING UNIT & ACCESSING SD CARD
To access Reset Button and
microSD™ card, remove cover using
a small screwdriver (included).
To reset the unit, (unit must be
connected to power) press the
Reset Button for 15 seconds or
until you hear an audible tone.
To remove microSD card, push
card in with your finger and release.
Card will eject halfway.
ADJUSTING FIXTURE
PARTS INCLUDED
(not drawn to scale)
4. Secure Mounting Gasket (5) and
Mounting Plate (6) to Mounting Bar (2)
using Mounting Bar Screw (9).
Do not over-tighten.
4. Secure Mounting Gasket (5)
and Mounting Plate (6) to
Mounting Bar (2) using Mounting Bar
Screw (9). Do not over-tighten.
CONNECT:
Black wire to“L” input.
Ground wire to “GND” input.
White wire to “N” input.
CONNECT:
Black wire to“L” input.
Ground wire to “GND” input.
White wire to “N” input.
7. Turn power On at circuit breaker or fuse box. Turn On wall switch
if connected to one. Ensure lights work before proceeding to step 8.
Continued
Continued
2. Install Mounting Bar (2) to an
External J-Box (1) using provided
J-Box Screws (3). Add Spacer (4)
to eliminate gap between Mounting Bar
and Mounting Plate.
1. Turn main power Off at circuit breaker or fuse box.
6. Position and align the Mounting Holes (11) on
Fixture Body (10) to the Mounting Plate Screws (8).
Secure Fixture Body (10) to Mounting Plate (6) using
Rubber Washers (12) and Decorative Nuts (13).
6. Position and align the Mounting Holes (11) on
Fixture Body (10) to the Mounting Plate Screws (8).
Secure Fixture Body (10) to Mounting Plate (6) using
Rubber Washers (12) and Decorative Nuts (13).
5. Connect power supply wires
directly to Terminal Block (7).
Secure wires to Terminal Block
by using a small screwdriver.
See below.
5. Connect power supply wires
directly to Terminal Block (7).
Secure wires to Terminal Block
by using a small screwdriver.
See below.
2. Install Mounting Bar (2) to a Flush J-Box (1)
using provided J-Box Screws (3). Add Spacer
(4) to eliminate gap between Mounting Bar
and Mounting Plate.
1. Turn main power Off at circuit breaker or fuse box.
3. Extend and feed J-Box wires through openings
on Mounting Gasket (5) and Mounting Plate (6).
3. Extend and feed J-Box wires through openings
on Mounting Gasket (5) and Mounting Plate (6).
8. Once fixture is tightly secured to J-Box, apply silicone sealant
around the base of the fixture to prevent moisture from reaching
the connections.
7. Turn power On at circuit breaker or fuse box. Turn On wall switch
if connected to one. Ensure lights work before proceeding to step 8.
8. Once fixture is tightly secured to J-Box, apply silicone sealant
around the base of the fixture to prevent moisture from reaching
the connections.
NOTE:
Tear away at perforation
on Mounting Gasket (5)
NOTE: Spacer (4) may or may not
be needed.
NOTE: Spacer (4) only needed if
J-Box is recessed too deep.
NOTE:
Do not tear away at perforation
on Mounting Gasket (5)
