13
en
Mount two new brushes, grinding or polishing tools.
Make sure that the drive pin on the tool holder (
11
)
engages in the hole on the disc.
Mount the clamping washer (
12
) and the clamping
screw (
14
) with the spring washer (
13
), and tighten the
clamping screw.
Mount the safety cover (
15
) and tighten the four screws
(
16
) again.
Switch the machine on and check the true running.
In the case of strong vibrations or noise, there
may be an imbalance on the brushes or on the
grinding or polishing tools. Replace out-of-bal-
ance application tools immediately! Pay attention
to the correct rotation direction of the applica-
tion tools!
Adjust the grinding rest (
7
) to the required height.
Adjust the required gap clearance with the handle
screw (
9
).
Operating instructions.
Switching on:
Disengage and fold up the safety pushbutton (
1
). Press
pushbutton
“I”
(
2
).
Switching off:
Fold up safety pushbutton (
1
). Press pushbutton
“0”
(
2
).
After switching off, the machine runs on for
approx. 50 seconds.
Safety pushbutton:
In situations of danger, press the safety pushbutton to
switch the machine off.
Reversing the speed.
Switch position 1: Low speed
Switch position 2: High speed
The speed may only be reversed with switch (
3
)
when the machine is stopped.
Overload protection.
In case of continuous high load over a longer period of
time, the machine is switched off. After a cooling-down
period of approx. 15 minutes, the machine is ready for
operation again.
Working a workpiece (figures 3+4).
Make sure that the safety cover (
15
) is securely closed.
Check the gap clearance of the grinding rest and ensure
that both fastening screws (
8
) are tightened.
Check the correct adjustment and the tight seating of
the spark guard (
4
).
Select the speed and switch the machine on.
Place the workpiece on the grinding rest and guide it
with both hands.
Extraction device
We recommend the use of an extraction device.
The machine can be connected via sleeve (
17
) to an
exhauster.
Noise emission values.
Repair and customer service.
Repairs may be carried out only by qualified per-
sons in conformity with the valid regulations.
For repairs, we recommend our FEIN customer service
centre, the FEIN authorised service centres and FEIN
agencies.
When the machine's power supply cable is damaged, it
must be replaced using a specially prepared power sup-
ply cable, available from your FEIN customer service
agent.
The current spare parts list of this machine can be found
on the Internet under www.fein.com.
Carry out the following maintenance regularly:
Blow out the cooling-air openings (
10
) of the
motor housing with compressed air.
Remove any deposits in the housing.
If required, you can change the following parts your-
self:
application tools, spark guard
Idle
Sanding
A-weighted emission
pressure power level
measured at the work-
place L
pA
(re 20 μPa),
in decibels
78.5
91
Measuring uncertainty
K
pA
, in decibels
4
4
Measured A-weighted
sound power level L
wA
(re 1 pW), in decibels
87
98
Measuring uncertainty
K
wA
, in decibels
2.5
2.5
Operating conditions
Speed (rpm)
3000
3000
Material
– Stainless steel
Dimension
–
Pipe, diame-
trer 42.4 mm
Wire brush
–
GRIT by Fein
0.35
REMARK: The sum of the measured emission value and
respective measuring inaccuracy represents the upper
limit of the values that can occur during measuring.
Wear hearing protection!
Measured values determined in accordance with the
corresponding product standard (see last page in this
Instruction Manual).
Summary of Contents for GRIT GIE Series
