Feig Electronic OBID i-scan ISC.PRHD102 Installation Manual Download

Page: 23 / 23

OBID

i-scan

UHF

Installation

ID ISC.PRHD102

FEIG ELECTRONIC GmbH

Page 23 of 23

M80601-4e-ID-B.docx

ANNEX

ANNEX A - Accessories

The following accessories are available for the Reader.

Table 7: Accessories

Feig Article No.

Name

Description

2650.000.00

ID CHA.NiMH-A

Battery charger with suitable connector for ID ISC.PRHD102-B

ANNEX B – Skope of Delivery

Table 8: Scope of delivery

Reader

Scope of delivery

ID ISC.PRHD102-B

- Reader ID ISC.PRHD102-B
- Quick user guide
- Configuration Software and Documenta-
tion download from “FEIG Public Download
Area”

ID ISC.PRHD102-USB

- Reader ID ISC.PRHD102-USB
- Quick user guide
- USB driver, Configuration Software and
Documentation download from
“FEIG Public Download Area”

NOTE:

Rechargeable batteries and battery charger are not included in delivery

FEIG Public Download Area:

http://www.feig.de/downloads-support.html

Username: LRU_MRU_PRHD
Password: uhf_reader

Summary of Contents for OBID i-scan ISC.PRHD102
























Search results

Summary of Contents for OBID i-scan ISC.PRHD102

Reviews:

Related manuals for OBID i-scan ISC.PRHD102

Brands by name

Popular brands

Feig Electronic OBID i-scan ISC.PRHD102, Installation Manual

Search results

Summary of Contents for OBID i-scan ISC.PRHD102

Reviews:

Related manuals for OBID i-scan ISC.PRHD102

Brands by name

Popular brands