manualshive.com logo in svg

Feig Electronic ID LRU500i-BD Series, Installation Manual

Share
Download
Feig Electronic ID LRU500i-BD Series Installation Manual Download Page 18

IDENTIFICATION 

ID LRU500i 

5  Terminals 

 

 

Installation 

Page 18 of 35 

 

 

5.5  Data-Clock Interface on Connector X3 

 

The data-clock (Wiegand) interface is connected via terminal X3. 
 
 
 
 
 
 
 
 
 
 
 

Pin Number at 

Connector X4 

Pin Assignment 

1 

Wiegand D1 

2 

Wiegand D0 

3 

GND 

 

Table 8: Pin Assignment Data-Clock (Wiegand) Interface 

 

NOTE: 

•

 

The data-clock interface is only available in Scan Mode in the reader version ID LRU500i-BD. 

•

 

The data-clock (Wiegand) interface cannot be used to configure the reader. 

•

 

For access control applications it is possible to connect the reader to two inputs of a Wiegand 

controller in parallel via an ID ISC.LR.WS-A Wiegand Switch and thus monitor two lanes (e.g. 

entrance and exit) simultaneously. 

 

 

 

Fig. 11: Pin assignment Data-Clock (Wiegand) interface on X3

 

Summary of Contents for ID LRU500i-BD Series




































Reviews:

No comments

Brands by name

Popular brands

Load more brands