Feider Machines FTDTR4870 Original Instructions Manual Download Page 5

5

Do not tilt the mower when starting the machine or turn on the engine, unless the mower
needs to be tilted for starting. In this case, do not tilt it more than absolutely necessary and
lift only the part that is furthest away from the user.

Do not start the machine by standing in front of the ejection

Do not place hands or feet near or under rotating parts. Keep clean the mouth of the grass
extractor.

Never take or carry the mower while the machine is running.

Stop the machine and remove the ignition key, disconnect the spark plug from the spark
plug:

o

Before cleaning or unclogging the grass extractor.

o

Before checking, cleaning, and working on the mower.

o

After hitting an object. Inspect the mower for damage and repair before re-using the
mower.

o

If the mower begins to vibrate abnormally, stop the engine immediately and check
according to previous recommendations.

The controls must be always checked if they are functioning correctly. In case of
malfunction, do not use the tool and bring to a service agent for inspection.

Stop the engine immediately:

o

Every time you leave the tool alone and the working area

o

Before refuelling.

When the tool is stopped, park it in a safe place.

Move slowly when moving.

The lawnmower should not be used in slopes and near drop-offs, ditches or embankments;
if the tool must be used in these kinds of emplacements, take an extreme precaution and
operate carefully the tool.

The lawnmower safety systems or features shall not be tampered with or disabled;

The operator should not alter or tamper with any sealed adjustments for the engine speed
control.

Maintenance and storage

Check and tighten all bolts and screws to ensure that the equipment is in safe operating
condition.

Never keep the mower with gasoline in the tank in a building or vapours can cause a bright
flame or spark.

Allow the machine to cool before storing it in an enclosed area.

To reduce the risk of fire, keep the machine clean without grass, without grease, the
muffler and the engine cools, disconnect the battery if necessary and empty the fuel tank

Check the grass catcher frequently, its condition or deterioration.

Replace worn and damaged parts for safety.

If the fuel tank is to be drained, it must be made outdoors.

Special safety instructions

Always use the mower with its pick-up bag and / or deflector in the intended position.

Switch off the engine before emptying the pick-up bag or before changing the cutting

Summary of Contents for FTDTR4870




























Reviews: