background image

 

DO  NOT  USE  THE  SANDER  WITHOUT  A  PROPER  ABRASIVE  SANDING  PAPER  INSTALLED

  (to 

prevent severe damage to the work). 

 

ABRASIVE PAD REPLACEMENT 

CAUTION: DISCONNECT SANDER FROM POWER SOURCE. 

 

1). Grasp the abrasive belt and strap support (tighten the plate on the bracket), to prevent rotation. 

2). Rotate the insert retaining nut counter clockwise and remove it.. 

3). Lift the large metal washer and the abrasive pad. 

 

NOTE: 

When the abrasive pad is removed from the sander, the abrasive rear disc is exposed. This rear disc 

is also covered with an abrasive material. 

 

This abrasive material is ONLY used to prevent "slippage" between the rear disc and the back abrasive plate 

foam.  It  is  NOT  suitable  for  use  as  an  abrasive  sander.  NEVER  USE  THE  SANDER  WITHOUT  PROPER 

ABRASIVE PAD INSTALLED (to prevent severe damage to the work). 

4). Position the new abrasive pad on the rear disc, making sure that the center hole in the abrasive disc is in 

the middle of the rear abrasive disc. 

5). Position the large metal washer of the retaining nut on the sander. 

6). Rotate the retaining nut clockwise and tighten by hand (while holding the abrasive pad).   

 

The output shaft is inserted at the centre of the adhesive disc with six angle wrench with clockwise rotation 

angle in the six hexagonal holes, and at the same time, the hands hold the adhesive disc. The grinding disc 

can be remove adhesive. 

 

TO CONNECTED WITH THE DUST COLLECTING BAG 

In order to protect the operator to reduce dust suction and site cleaning process at work, in the work 

process please connect the machine with dust bag. As shown in the figure is connected with the suction 

pipe, the other end is connected with the dust collecting bag. 

CAUTION:

 

Failure to use a dust bag rated for drywall dust will increase the level of airborne dust 

particles in the work area. Continued and prolonged exposure to high concentrations of airborne dust 

may affect the respiratory system function. 

Summary of Contents for FPEP850LED















Reviews: