![background image](http://html1.mh-extra.com/html/federal-signal-corporation/smartsiren-platinum-ssp2000b/smartsiren-platinum-ssp2000b_quick-connect-manual_3808266002.webp)
Quick Connect Guide: SSP3000B/SSP2000B System LED Indicators, Fuses, and Volume Controls
External Fuses at a Glance
Each external mini ATM fuse on the
SSP3000B has an integrated LED that glows
when the fuse is blown. The table identifies
the color code and amperage. (Fuses on
the SSP2000B do not have lights.)
Color
Amp.
Tan
Red
Yellow
Front of Siren Amplifier/Relay Module
(SSP3000B shown)
Front of Control Pad
SLIDE SWITCH LEDs: LEDs above the slide
switch glow when the system is on (
1
=green,
2
=amber,
3
=red). The LED brightens above
the position in which the slide switch is placed.
Amber
L
EDs: LEDs mimic these active
S
ignal
M
aSter
patterns: Left, Right,
Center-Out, or Warn patterns 1–4.
Button LEDs: All buttons on the control
pad glow red when the system is on.
Pressed buttons glow brighter to indicate
that the function they control is active.
Back of Control Pad
PWR: LED glows when the
siren siren system has power.
SIREN 20 A: 20 A fuse for the siren.
5A HORN: 5 A fuse for horn-ring circuit.
PA VOL: Screw for adjusting the factory-set
PA volume. Only on select models with the
microphone connector on the siren system.
RAD VOL: Screw for adjusting the factory-set
radio rebroadcast volume.
AUX 11–14: LED glows when the output
is on for a 2 A auxiliary solid-state relay.
These relays are active-high only and are
internally protected by electronic short-
circuit detection circuits.
AUX 1–10: LED glows on the SSP3000B
when the output is on for an 10 A auxiliary
solid-state relay. Relays 9/10 can be
configured as 12 Vdc out or ground out.
LIGHTBAR ACTIVE: LED glows
on the SSP3000B when the
lightbar is flashing.
AUX PWR: LED glows on the
SSP3000B when battery power
and serial cable power are
present.
SM PWR: LED glows on the
SSP3000B when the
S
ignal
-
M
aSter
has power.
SM ON: LED glows on
the SSP3000B when the
S
ignal
M
aSter
flashes.
RX (Receive): LED flashes on the SSP3000B
when the siren system receives a message
on the FS
C
onvergenCe
network.
TX (Transmit): LED flashes on the
SSP3000B when the siren system transmits a
message on the FS
C
onvergenCe
network.
10 A AUX 1–10: 10 A fuses for
10 A auxiliary solid-state relays.
Relays 9/10 can be configured
as 12 Vdc out or ground out.
Relays 7, 8, and 9 are not
available on the SSP2000B.
SM 20A: 20 A fuse (
S
ignal
M
aSter
)
INPUT 1–4: LEDs glow on
the SSP3000B when an input
is receiving a signal. Voltage
and amperage are required
for the signal.
KEYPAD: The keypad legends in the illustration are
for a typical configuration. The SSP3000B kit includes
additional legends. All buttons are programmable.
+
–
PA VOL: Screw for adjusting the factory-
set public address volume.
S
ignal
M
aSter
and
C
onvergenCe
are trademarks of Federal Signal Corp.
© 2014 Federal Signal Corporation. All Rights Reserved.