Federal Signal Corporation Reliant Installation Maintenance And Service Manual Download Page 20

Page: 20 / 20

Getting Technical Support and Service

Reliant

™

Light Bar

Federal Signal www.fedsig.com

Ordering Replacement Parts

To order replacement parts, call Customer Support at 1-800-264-3578, 7 a.m. to 5 p.m.,

Monday through Friday (CST) or contact your nearest distributor.

Table 6 Replacement parts

Description

Part No.

Clear Dome

858003474

Amber Dome

858003474-02

Blue Dome

858003474-03

Red Dome

858003474-04

Clear Lip Seal (6 feet per section)

8583020-01

End PCB Assembly (Configured)

Contact Factory

Intermediate PCB Assembly (Configured)

Contact Factory

2645 Federal Signal Drive

University Park, Illinois 60484-3167
www.fedsig.com
Customer Support

Police/Fire-EMS:

800-264-3578 • +1 708 534-3400

Work Truck:

800-824-0254 • +1 708 534-3400

Technical Support

800-433-9132 • +1 708 534-3400

Summary of Contents for Reliant




















Search results

Summary of Contents for Reliant

Reviews:

Related manuals for Reliant

Brands by name

Popular brands

Federal Signal Corporation Reliant, Installation Maintenance And Service Manual

Search results

Summary of Contents for Reliant

Reviews:

Related manuals for Reliant

Brands by name

Popular brands