Federal Signal Corporation RB-CAP11 Manual Download Page 3

Mounting Rumbler

®

 Speakers in a 2011 and Newer Chevy

®

 Caprice

3

Model RB-CAP11 Speaker Mounting Kit

Product Overview

The RB-CAP11 is a mounting kit for the Federal Signal Rumbler

®

 low-frequency signaling system. This kit 

mounts one speaker in each side of the rear bumper of a 2011 and newer Chevy Caprice.

Unpacking the Kit

After unpacking the kit, inspect it for damage that may have occurred in transit. If it has been damaged, do 
not attempt to install or operate it. File a claim immediately with the carrier, stating the extent of damage. 
Carefully check all envelopes, shipping labels, and tags before removing or destroying them. Ensure that the 
parts listed in Table 1 are included in the package. If you are missing any parts, contact Customer Support at 
1-800-264-3578, 7 a.m. to 5 p.m., Monday through Friday (CT).

Table 1

  Kit contents

Qty. Description

Part Number

2

Band, Long

82831114

2

Band, Short

82831115

4

1/4

"

 x 5/8

"

 Screw, Type B

7011165-10

2

5/16

"

-18 Cap Hex Hd. Screw

7002A005-20

6

5/16

"

 Lockwasher

7074A020

6

5/16

"

-18 Hex Nut

7059125

4

5/16

"

-18 Mach. Hex Hd. Screw

7000469-40

4

5/16

"

 Flat Washer

7072A031

8

Spacer, Bronze

230301

2

Bracket, Step

82831120

2

Shield, Tail Pipe

82831121

4

Clamp, #36, Worm Drive, SS

150201

Mounting the Rumbler

INSTALLATION PRECAUTION

Do not install the speaker near the fuel tank or fuel 

lines. Installing the speaker too close to fuel line/tank areas may cause fuel leakage 
or fire during a vehicle collision, causing personal injury or death.

USE ONLY WITH RUMBLER AMPLIFIER

This speaker is designed to be used only 

with the Rumbler Amplifier. Do not connect this speaker directly to a standard 
electronic siren. Connecting this speaker directly to a standard electronic siren will 
greatly reduce the effectiveness of the siren signal. When installing this speaker, 
always refer to the Rumbler low-frequency amplifier installation and operating 
instructions (part no. 2562420) for more detailed information about the siren system 
and how to install, service, and operate the system safely. Instruction manuals are 
available for viewing or downloading at www.fedsig.com.
Failure to follow all safety precautions and instructions may result in property 
damage, serious injury, or death.

Summary of Contents for RB-CAP11













Reviews: