background image

Warranty

 – Seller warrants all goods for five years on parts and 2-1/2 years 

on labor, under the following conditions and exceptions: Seller warrants that 

all goods of Seller's manufacture will conform to any descriptions thereof for 

specifications which are expressly made a part of this sales contract and at the 

time of sale by Seller such goods shall be commercially free from defects in 

material or workmanship. Seller reserves the right at the Seller’s discretion 

to “Repair and Return” or “Replace” any item deemed defective during the 

warranty period. This warranty does not cover travel expenses, the cost of 

specialized equipment for gaining access to the product, or labor charges for 

removal and reinstallation of the product. This warranty shall be ineffective 

and shall not apply to goods that have been subjected to misuse, neglect, 

accident, damage, improper maintenance, or to goods altered or repaired by 

anyone other than Seller or its authorized representative, or if five years have 

elapsed from the date of shipment of the goods by Seller with the following 

exceptions: lamps and strobe tubes are not covered under this warranty. 

Outdoor warning sirens and controllers manufactured by Federal Warning Sys-

tems are warranteed for two years on parts and one year on labor. No agent, 

employee, representative or distributor of Seller has any authority to bind the 

Seller to any representation, affirmation, or warranty concerning the goods 

and any such representation, affirmation or warranty shall not be deemed to 

have become a part of the basics of the sales contract and shall be unenforce-

able. THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU 

OF ALL OTHER WARRANTIES OR MERCHANTABILITY, FITNESS 

FOR PURPOSE AND OF ANY OTHER TYPE, WHETHER EXPRESS 

OR IMPLIED. These warranties shall not apply unless Seller shall be given 

reasonable opportunity to investigate all claims for allegedly defective goods. 

Upon Seller's instruction a sample only of allegedly defective goods shall be 

returned to Seller for its inspection and approval. The basis of all claims for al-

leged defects in the goods not discoverable upon reasonable inspection thereof 

pursuant to paragraph 8 hereof must be fully explained in writing and received 

by Seller within thirty days after Buyer learns of the defect or such claim shall 

be deemed waived.

Industrial Systems

2645 Federal Signal Drive • University Park, IL 60484-3167
Tel: 708-534-4756 • Fax: 708-534-4852
Email: [email protected] • www.federalsignal-indust.com

Summary of Contents for Commander 371ST-250

















Reviews: