FEB HV5120-S Series Product Manual Download Page 4

23 

 

 

2.

 

Safety Precautions 

 

Alert 

1)

 

It is important and necessary to read the user manual carefully (and attachment) before installing or using 
battery. Failure to do so or to follow any instruction or warning in this document can result in electrical 
shock, serious injury, and death, or damage battery, potentially rendering it unusable. 

2)

 

When battery is stored for a long time, it is required to charge once every 6 months, and the SOC should be 

no less than 85%. 

3)

 

After battery module cannot be discharged, it needs to be recharged within 12h. 

4)

 

Do not connect power terminal reversely. 

5)

 

All power supplies must be disconnected during maintenance. 

6)

 

Please contact the supplier within 24 hours if there is something abnormal. 

7)

 

Do not use any liquid to clean the battery. 

8)

 

Do not expose battery to flammable or irritating chemicals or vapor. 

9)

 

Do not paint any part of battery, including any internal or external components. 

10)

 

Do not connect battery with PV solar wiring directly. 

11)

 

Do not install or use this product beyond provisions of the manual. 

12)

 

Direct or indirect damages caused by the above reasons are not covered by warranty claim. 

 

 

Warning

 

2.1

 

Before Connecting 

1)

 

Please check the external packaging condition before unpacking. If it is damaged, contact corresponding 
local retailer. 

2)

 

After unpacking, please check the products and spare parts according to spare parts list. If the product is 
damaged or missing, please contact your local retailer. 

3)

 

Connect to specified matching inverter. 

4)

 

Before installation, be sure to cut off the grid power and make sure battery is in turned-off mode. 

5)

 

It is prohibited to connect the battery and AC power directly. 

6)

 

Embedded BMS in the battery is designed for 24VDC. 

7)

 

All electrical wiring must be connected in accordance with local regulations. 

8)

 

Please ensure that electrical performance of battery system is compatible with the equipment. 

9)

 

The installation onsite shall be equipped with fire-fighting facilities that meet relevant requirements, such 
as fire sand, dry powder fire extinguisher, etc. 

 

 

2.2

 

In Using 

1)

 

If battery system needs to be moved or repaired, power must be cut off and battery is completely shut 

down. 

2)

 

It is prohibited to connect battery with different types of battery. 

Summary of Contents for HV5120-S Series






















Reviews: