background image

TROUBLESHOOTING 

MT86/MT86HT Flow Meter 

22 

Fluid Components International LLC 

If the flow element is bad, replace it with a spare flow element. Return the bad flow element to FCI for repair and, or replacement. See 

Appendix C for the Customer Service return procedure. 

Troubleshooting Process - Voltage Measurements 

Verify the use of the correct power source. Verify the power source is on and that the wiring matches the wiring diagram in 

Figure 3

 in 

INSTALLATION

If the flow element resistance and wiring check out, recheck the power supply; the fuse and the AC and DC voltages. 
If there are multiple failures in the flow meter, the power supply is suspect. 
Perform the following voltage checks with power applied to the flow meter. Place the flow meter in normal operating conditions. Make all 

measurements with the use of a DMM that has a differential (non-grounded) input. 

Note: 

The flow element sensing point voltage readings are for 1000 ohm RTDs. 

Power Supply Source Voltages 

Measure the power source at the power supply terminal block TS1 to be sure the correct power is applied. 
Check the power supply voltages, using the test points provided. See 

Table 5

 and 

Figure 11

 for the proper operating voltages. If the 

voltage checks are correct, the power supply is functioning properly. 

Table 5 – Power Supply Voltages, Power Supply Board 

Positive Lead (+) 

Negative Lead (-) 

Measured Value 

TP1 

TP4 

28 VDC ± 1 VDC 

TP2 

TP4 

15 VDC ±  .6 VDC 

TP3 

TP4 

5 VDC ± .3 VDC 

TP5 

TP4 

-5 VDC ± .3 VDC 

TP6 

TP4 

-15 VDC ± .6 VDC 

VC6 

VGND 

-26.43 VDC ± 1 VDC* 

VC1 

VGND 

43.4 VDC ± 2 VDC* 

*Measurement points are not available on some power supplies. 

If operating power is at terminal block TS1 and the test points do not have power, check fuse F1 on the power supply board. 
Remove power and unplug the power supply from the control board. Apply power to the power supply and re-measure the voltages as 

shown i

Table 6

. If the voltage is still missing, then remove and replace the power supply. 

Make the following measurements at the control board terminal strip. See 

Table 6

 and 

Figure 12

 for the measurements. 

Table 6 – Power Supply Voltages, Control Board 

Positive Lead (+) 

Negative Lead (-) 

Measured Value 

TP15 

TP16 

10 VDC ± .02 VDC 

RN1 Pin 3 

TP16 

5 VDC ± .04 VDC 

U5 PIN 7 

TP16 

-10 VDC ± .06 VDC 

 

Summary of Contents for MT86























































Reviews: