t
800.900.1730
f
630.889.8106
3609 Swenson Ave. St. Charles, IL 60174
Apply Silicone Bead
THIS DOCUMENT IS PROPRIETARY TO FC LIGHTING, INC. ANY UNAUTHORIZED TRANSFER, USE OR REPRODUCTION IS STRICTLY PROHIBITED.
©2016 FC LIGHTING, INC.
FCSL100 SERIES
-
INSTALLATION INSTRUCTIONS
page 1 of 2
CAUTION: BEFORE CONNECTING THE FIXTURE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.
NOTE
:
Faceplates
- The Faceplate type used determines fixture installation.
FCSL101-FCSL106 mounts flush to front of Fixture Lip. (Fig. 1) and
B
(HB)
FCSL108-FCSL110 fits over (wraps around) Fixture Lip. (Fig. 2) and
C
(DWR)
GENERAL
:
1. Before starting the installation, make sure all electricity has been turned off and electrical
breaker has been locked out and tagged out.
2. To ensure the success of the installation, be sure to read these instructions and review the
diagrams thoroughly before beginning.
3. All electrical connections must be in accordance with local codes, ordinances, or the
National Electrical Code.
NOTE
: The important safeguards and instructions appearing in this manual are not meant to
cover all possible conditions and situations that may occur.
INSTALLATION INSTRUCTIONS:
A) Remove the two (2) socket head screws holding Lens and Faceplate to fixture. Then remove
internal lamping components (guts) from fixture.
FOR CONCRETE POUR:
Be sure to level and stabilize fixture. Cover any holes and knockouts on
fixture housing to prevent leakage. Seal the fixture to prevent water leakage during operation.
FOR DRYWALL MOUNT:
Cut hole in drywall (2-5/8” x 9-3/8”) for flush mount
B
or
(2-5/16” x 8-5/16”) for front mount
C
. Refer to detailed instructions on page 2.
NOTE
: PL version is not for through wiring. All connections must be water tight.
1) Connect conduit or code approved electrical fitting through one of the 7/8” diameter holes
on the back or side of the fixture. Secure fixture housing to forms outside of gasket area.
Refer to Fig. 3 on pg. 2 using Hanger Brackets and Drywall Adapters for Front Mounted
drywall application.
2) After fixture is mounted, connect your ground wire to green ground wire on fixture.
3) Replace internal components with approved lamp.
4) Attach lens and frame, replace two (2) socket screws tightening evenly.
5) Restore power and test fixture. If fixture does not turn on, disconnect power before
checking for problems.
IMPORTANT:
Fixtures are listed for installation with liquid tight or rigid wall conduit only.
D
Fixtures installed without a silicone bead will void the warranty.
DETAILED ILLUSTRATION
JO Rev.
0218
Fig. 3
Drywall Adapter
(DWR)
Drywall Adapter
Tighten
Screw
Adapter holds
Fixture in place.
Adapter Screw
Back of Fixture
Front of Fixture Lip Mounted Flush with Wall.
Use
HB
for proper installation.
Fixture Lip Mounted in Front of Wall.
Use
DWR
for proper installation
Fixture Lip in Wall
Same for concrete or drywall application.
Same for concrete or drywall application.
Fixture Lip against Wall
Fixture Lip
Gasket Area
A
B
C
Mounting for
Fig. 1
Faceplate type.
Mounting for
Fig. 2
Faceplate type.
BOSS REQUIRED FOR GROUND SCREW.
8MM OD X 8MM TALL BLIND TAP 6-32, 8MM DEEP
2.64 in
INSERT TYP2
8-32 THREADED
2.8 in
BLIND HOLE TYP 4
3 X 6MM DEEP
22.23 TYP 2
2 x 1MM DEEP
TYP 2
.125 in
9.375 in
3 in.
BOSS REQUIRED FOR GROUND SCREW.
8MM OD X 8MM TALL BLIND TAP 6-32, 8MM DEEP
2.64 in
INSERT TYP2
8-32 THREADED
2.8 in
BLIND HOLE TYP 4
3 X 6MM DEEP
22.23 TYP 2
2 x 1MM DEEP
TYP 2
.125 in
9.375 in
3 in.
Fig. 1
Faceplate mounts to
Front of Fixture Lip.
Use mounting
B
Fig. 2
Faceplate fits
over Fixture Lip.
Use mounting
C
Fixture Lip
BOSS
REQUIRED
FOR GROUND
SCREW.
8MM
OD
X 8
MM
TAL
L BLIN
D TAP
6-32
, 8MM
DEEP
2.64 in
INSER
T TYP2
8-32
THRE
ADED
2.8 in
BLIN
D HO
LE
TYP
4
3 X
6MM
DEE
P
22.23 TYP 2
2 x
1MM
DEE
P
TYP 2
.125 in
9.375 in
3 in.
Back of Fixture
1/2” trade connector openings
Fixture Lip
Fixture Housing
BOSS REQUIRED FOR GROUND SCREW.
8MM OD X 8MM TALL BLIND TAP 6-32, 8MM DEEP
2.64 in
INSERT TYP2
8-32 THREADED
2.8 in
BLIND HOLE TYP 4
3 X 6MM DEEP
22.23 TYP 2
2 x 1MM DEEP
TYP 2
.125 in
9.375 in
3 in.
D
Apply Silicone Bead
D
