33
INPUTS & OUTPUTS
XLR CONNECTION
Available on MUSE 210LND model
The XLR connection is a type of balanced connection that allows the
connection of devices over long distances without loss of quality due to
the background noise detected.
This is made possible by the presence, as well as by the mass (pin 1), of
two cables: a signal cable (pin 2) and a 180° dephased signal cable (pin 3);
at the opposite end of the signal source, on both these cables, in addition
to the actual signal, the same quantity and type of background noise
possibly detected along the path or inevitably produced by the cables
(not the one for thermal agitation) will be present in phase. The signal
will then be taken from the two cables by g present in phase on
both cables, will be cancelled by the difference operation. In the three-
pin version it is normally used for the termination of balanced audio
lines but it is often also used for unbalanced signals creating a short
circuit between the mass and the cold pin. The EIA RS-297-A standard
requires that the three-pin XLR connectors for balanced audio are
wired as shown in fig.
ETHERNET CONNECTION
Available on MUSE 210LND model
Neutrik etherCON
®
connectors provide solutions for data transfer and
more in harsh and demanding environments.
The etherCON
®
series is a robust and lockable RJ45 connector
system optimized for professional audio, video and lightning network
applications.
Thanks to the possibility of networking, the models of the Horizon
series can be remotely controlled thanks to the INFINITO System
Management Suite software.
It is advisable to use a cat.5e SF / UTP or higher class ethernet cable.
Support for DANTE Digital Sudio Networking
SPEAKON
Available on MUSE 210L model
MUSE210L is a bi-amplified 2-way system, it needs to be driven by two
amplification channels, one for the LF section and one for the HF section.
Internally there is a protection on the HF channel that eliminates low
frequencies in case of connection error, but there is no passive crossover.
Nominal impedances are 16 Ohm for LF and 32 Ohm for HF. In the rear
panel there are two NeutriK Speakon NLT4 connectors with the 4 pins
connected in parallel to each other. In this way it is possible to connect
two or more speakers by connecting them in cascade with a 4-conductor
cable.
MUSE210L is a very complex acoustic system and needs to be driven
by processed amplifiers (with DSP on board) configured with presets
created specifically by FBT Elettronica. The use of the MUSE system
with presets not validated by FBT or even without any specific preset, in
addition to not guaranteeing adequate performance, puts the reliability
of the internal components at risk and is therefore absolutely prohibited.
Unprocessed amplifiers can also be used, but connected upstream
with a Digital Loudspeaker Processor with a preset authorized by FBT
Elettronica which guarantees correct alignment, equalization and
protection of the system.
LINK OF TWO OR MORE SPEAKERS
Attention!
In this configuration it is necessary to choose an amplifier
capable of driving a load resulting from the parallel of the speakers
connected both in the LF and HF way.
The section of the SPEAKON cable must be suitable for the current
Precision Coverage Vertical Passive Array
210L
Nominal Impedance (LF/HF):
Recommended Amp. (LF/HF):
Long Term Power (LF/HF):
Sensitivity @1W,1m (LF/HF):
Max SPL (cont./peak):
Horizontal Dispersion:
16/32 Ohm
800/200W RMS
400/100W
101/112 dB
128/135
90
°
CAUTION: IT IS ADVISABLET O USE
AN AMPLIFIER WITH AN RMS
OUTPUT POWER ACCORDING TO
TECHNICAL SPECIFICATIONS.
IN
LINK
1
LF+
LF-
HF+
HF-
SPEAKON
NLT4
INPUT
1+
1-
2+
2-
SPEAKON
NLT4
OUTPUT/LINK
1+
1-
2+
2-
supplied to the speakers. We generally recommend using the following
sections
4 wires x 2.5mm
2
length up to 20mt
4 wires x 4mm
2
over 20 meters
ground
hot
cold
ground
hot
cold
LINK (uscita)
XLR bilanciato femmina
INPUT
XLR bilanciato maschio
