Fayat DYNAPAC DFP8 Operatinginstructions And Maintenance Download Page 19

Page: 19 / 110

Examples for improper use are:

dragging the machine along as a measure of transportation

throwing the machine off the transport vehicle

attaching an additional weight to the machine

It is not permitted to stand on the machine while working.

Lifting tackle must be removed before starting work.

Starting and operating the machine in explosive environments and

in underground mining is prohibited.

The lifting and lashing points specified in these instructions must

be used. It is prohibited to use other lifting and lashing points (e.g.

guide handle, steering rod).

3.1.6 Estimated service life of the machine

If the following general conditions are met, the estimated service

life of the machine is usually in the range of several thousand oper-

ating hours:

Regular safety inspections by an expert / qualified person

Performance of the prescribed maintenance work within the

specified time

Immediate performance of necessary repair work

Exclusive use of original spare parts

Concerning your safety – Basic prerequisites

DFP8

Summary of Contents for DYNAPAC DFP8















































































































Search results

Summary of Contents for DYNAPAC DFP8

Reviews:

Related manuals for DYNAPAC DFP8

Brands by name

Popular brands

Fayat DYNAPAC DFP8, Operatinginstructions And Maintenance

Search results

Summary of Contents for DYNAPAC DFP8

Reviews:

Related manuals for DYNAPAC DFP8

Brands by name

Popular brands