manualshive.com logo in svg

Faulhaber MC 5010, Communications Manual, Page: 24 / 43

Share
Download
Faulhaber MC 5010 Communications Manual Download Page 24

 

 

3 Protocol description 

15-04-2016 24 7000.05052 

Block transmission aborted by the master (Abort SDO telegram) 

Tab. 22:  Request Abort SDO Transfer 

Byte 

Contents 

Description 

1 

11 

User data length 11 bytes 

2 

Node number 

Node number 

3 

0x03 

Command SDO Error 

4 

Index LB 

Index of the object entry LB 

5 

Index HB 

Index of the object entry HB 

6 

Sub-index 

Sub-index of the object entry 

7 

Error0 

Additional error code LB (see Tab. 23, p. 24) 

8 

Error1 

Additional error code HB (see Tab. 23, p. 24) 

9 

Error2 

Error code (see Tab. 23, p. 24) 

10 

Error3 

Error class (see Tab. 23, p. 24) 

11 

CRC 

Check sum 

 

Error byte coding 

If an abort occurs due to an error in the SDO protocol the bytes 7 to 10 (error 0 to error 3) 
are coded. 

Tab. 23:  Error byte coding 

Error class  Error code  Additional 

code 

Description 

0x05 

0x04 

0x0001 

SDO command invalid or unknown 

0x06 

0x01 

0x0000 

Access to this object is not supported 

0x06 

0x01 

0x0001 

Attempt to read a write-only parameter 

0x06 

0x01 

0x0002 

Attempt to write to a read-only parameter 

0x06 

0x02 

0x0000 

Object not present in the object dictionary 

0x06 

0x04 

0x0043 

General parameter incompatibility 

0x06 

0x04 

0x0047 

General internal incompatibility error in the device 

0x06 

0x07 

0x0010 

Data type or parameter length do not match or are unknown 

0x06 

0x07 

0x0012 

Data types do not match, parameter length too long 

0x06 

0x07 

0x0013 

Data types do not match, parameter length too short 

0x06 

0x09 

0x0011 

Sub-index not present 

0x06 

0x09 

0x0030 

General value range errors 

0x06 

0x09 

0x0031 

Value range error: Parameter value too large 

0x06 

0x09 

0x0032 

Value range error: Parameter value too small 

0x06 

0x09 

0x0036 

Value range error: Maximum value greater than minimum value 

0x08 

0x00 

0x0000 

General SDO error 

0x08 

0x00 

0x0020 

Cannot be accessed 

0x08 

0x00 

0x0022 

Cannot be accessed at current device status 

Summary of Contents for MC 5010












































Reviews:

No comments