fatboy HOTSPOT FAMILY, Manual

Page: 13 / 32

12 EN - 12
Charging the battery
To fully charge the battery, allow approximately 3
hours of charging. Check the led indicators on the
red Fatboy label for the battery status. The battery
is charging when the indicator is blinking. When
all four LED’s are lit constantly the battery is fully
charged. When the Hotspot turns off by itself (after
a blinking battery indicator), it indicates the battery
needs to be charged.
Check battery: press and hold the heat button ( in
the ‘O’ of the Fatboy logo) for 2 seconds to see the
battery indicator.
The battery indicator on the label shows the
battery capacity by 4 LED’s.
4 LED’s on: 100-75%
3 LED’s on: 75-50%
2 LED’s on: 50-25%
1 LED on: 25-0%
Turn on/off and change temperature
Hotspot can easily be turned on by pressing the
On/off button on the back off the Fatboy label.
The Hotspot has three heatsettings, indicated by
the LED’s on the label. These heatsettings can be
controlled by the heat button ( in the ‘O’ of the
Fatboy logo) on the front.
• Turn ON: Press the button on the back of
the label.
• Start heatsetting LOW: Press the heat button
once to get 28 to 32 degrees Celsius
• Start heatsetting MEDIUM: Press the heat
button twice to get 34 to 38 degrees Celsius (not
intended for extended use)
• Start heatsetting HOT: press the heat button
three times to get 38 to 42 degrees Celsius (not
intended for extended use)
• Turn OFF: Press the button on the back of the
label to turn Hotspot off at any given time.
Maintenance:
If you don’t use the Hotspot for a longer period of
time, please make sure you recharge the battery
at least every three months to keep the battery in
good condition.
Cleaning:
- Hotspot Quadro cover: handwash only.
Please remove the cover before washing, and take
the innerbag and electronics out.
NOTE: THE FILLING AND ELECTRONICS ARE NOT
WASHABLE and should be kept dry.
- Hotspot Lungo cover: handwash only.
Please remove the cover before washing, and take
the innerbag and electronics out.
NOTE: THE FILLING AND ELECTRONICS ARE NOT
WASHABLE and should be kept dry.
- Hotspot Blanket: handwash only.
Please remove the fatboy label and battery
before washing.
Do not use cleaning agents which contain alcohol,
benzene, abrasive substances or chemicals.
Trouble shooting:
The HOTSPOT is not working well:
The Hotspot is not turning on:
Please make sure to press the on/off switch at
the BACK of the label first before you are able to
operate the heatsettings using the button on the
FRONT of the Fatboy label. This is a safety measure
to avoid the Hotspot from turning on accidentally.
The Hotspot is not responding at all when pressing
the on/off switch followed by the switch on the
front side of the label:
• charge the Hotspot only using the adapter and
usb cable provided with Hotspot
• By installing the charger the indicator lights
on the Fatboy label should light up (blinking)
indicating the charging process has started.
The product is still not responding:
If the product is not responding to the connection
of the charger, take the following steps:
1. please open-up the cover for the Hotspot Pillow
or Blanket .
2. check the connection of the control board inside
the label to the battery. These two are connected
by a barrel plug.
3. Check if the connection is connected properly.
4. Check the connection of the control board inside
the label to the heat pad at the same time.
Try to turn it on again, and check if the product
responds to the charger one final time.
The Hotspot is not turning off:
The Hotspot can be turned off using the switch at
the back of the label. In case you are not able to
turn Hotspot off please disconnect the battery pack
and get in touch with your Fatboy dealer.
If these instructions did not solve the issue, please
get in touch with Fatboy or your local Fatboy dealer
IMPORTANT!
Please contact your Fatboy® dealer
if you have any problems.
Technical specifications:
Model: Fatboy® Hotspot
Secondary rating (adapter recommendation):
5 VDC 2.4 A, MKC-0502400SEUU.
Safety Class: Class II (For adapter)
Connection: USB to Magnetic Pogo Pin charger
Heat source: Carbon mesh / Composite wire
Switch: Built-in three step heat control.
IP value: IP20 (For adapter)
Ambient temperature: -10 to 40 ºC
Materials: Polyester
Internal battery: Lithium-ion battery 10,8V
2600mAh.