background image

WARNING:

 

Always operate this product in a safe and responsible manner and observe local laws. 

WARNING:

 The Shark Byte by Fat Shark is not a toy. This product contains small parts and is intended to be 

operated by adults. Not for children under 14 years old.

WARNING:

 The Shark Byte by Fat Shark requires soldering for assembly and is not recommended for beginners. 

Assemble at your risk, damage to the product from incorrect assembly is not covered under warranty.

Shark     Byte

Shark Byte User Manual

Rev. 121220(DDMMYY) 

For more product information, please visit:

www.fatshark.com

All Rights Reserved

THIS MANUAL COVERS

NOT INCLUDED, REQUIRED

•  Video Goggles (Fat Shark Dominator Series)
•  (1) 5.8GHz antenna with MMCX connector, to be mounted on your drone (TX5M.1)
•  (1) 5.8GHz antenna with u.FL connector, to be mounted on your drone (TX5S.1)
•  (2) 5.8GHz antenna(s) with SMA connectors, to be mounted on the vrx (RX5.1) 
•  Batteries

FSV2476

Shark Byte Video Receiver RX5.1

FSV2477

Runcam Nano HD Camera

FSV2478

Shark Byte Video Transmitter TX5M.1

FSV2480

Shark Byte Video Transmitter TX5S.1

Summary of Contents for Shark Byte RX5.1

















Reviews: