background image

Technical Specifications 

VIM301 

V I M 3 0 1   U s e r   M a n u a l

11 

© 2 0 1 5   F a s t w e l

v . 0 0 2

2.2 

Power Requirements 

The power to the module is supplied via PCI/104 and PC/104 (if installed) connectors. 

Note... 

The auxiliary power connector (XP1) is optional. If the module is powered via the auxiliary 
power connector, +5V and +12V voltages are supplied to PC/104-Plus connectors as well. 
Make sure that not more than one power supply unit is connected to +5V and +12V lines. 

Table 2.1: 

Power Supply Requirements 

Connector 

Power Voltage, V 

Power Voltage Range, 

Version 

Consumption 
Current, A 

PC/104 and 
PCI/104 

+5

from +4.75 to +5.25 

VIM301-01 

0.6 

VIM301-02 

VIM301-03 

0.6 

VIM301-04 

0.6 

VIM301-05 

The +12 V voltage is not used by the module itself, it is routed to XP4 and XP11 connectors. 
The consumption current and voltage limits depend on the Planar display type and power 
consumption of video cameras. 

2.3 

Environmental 

2.4 

Operating temperatures: from 

–40ºC to +85ºC;

Storage temperature: 

–55

C to +90

C

;

Relative humidity: 5% to 90% at +

25°C, noncondensing

Mechanical

Vibration 

– 10g;

Single shock, peak acceleration 

– 150 g;

Multiple shock, peak acceleration 

– 50 g.

2.5 

Dimensions and Weight

Weight: 0.12 kg

Overall and mounting dimensions are presented in the figure below. 

Summary of Contents for VIM301























































Reviews: