background image

Page 11

STEP 8

To couple your trailer:

Back the hitch ball under the 

coupler.  Retract the tongue jack 

until the coupler rests on the hitch 

ball.  Lock the coupler.  If you are 

using a weight distributing hitch, 

extend the jack and tension the 

weight distribution bars.  

Retract the jack completely until 

the flip rotates up and out of the 

way for towing.  Do not force the jack handle after the jack has reached the top of 

travel.  Rotate it back slightly if necessary for towing.

Don’t force jack.  Rotate back 

slightly if necessary.

Limited One Year Warranty

Progress Mfg. Inc. warrants, to the original purchaser, this product against 

defects in materials and workmanship for a period of one year from date of 

purchase. This warranty does not cover damage due to normal wear and 

tear, misuse, neglect, abuse, or product finish. Progress Mfg. Inc. reserves the 

right to repair or replace the defective part(s) at their discretion. Replace-

ment of product or refund constitutes the fulfillment of all liabilities of Prog-

ress Mfg. Inc. under this warranty. For questions about warranty coverage 

and warranty authorization, please call (877) 523-9103. If warranty repair 

or replacement is approved, send the entire product and proof of purchase, 

shipping pre-paid, to: Progress Mfg. Inc., 533 South 500 West, Provo, UT 

84601

A Product of Progress Mfg. Inc.

Summary of Contents for flip 88-00-6525













Reviews: