・
Specifications are subject to change without notice
・
For more information, questions and comments regarding products, please
contact us below.
91 Awata-cho Chudoji Shimogyo-ku Kyoto 600-8815 Japan
TEL: +81-(0)75-325-2920
FAX: +81-(0)75-325-2921
Website
http://www.optex-fa.com
CAUTION
WARNING
●
The light source of this product applies the visible light semicon-
ductor laser. Do not allow the laser beam to enter an eye, either
directly or reflected from reflective object. If the laser beam ente-
rs an eye, it may cause blindness.
●
This product is not an explosion proof construction. Do not use the
product under flammable , explosive gas or liquid environment.
Do not disassemble or modify the product since it is not designed
to automatically stop the laser emission when open. Disassembling
or modifying at customer's end it may cause personal injury, fire or
electric shock.
●
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation
exposure.
●
●
It is dangerous to wire or attach/remove the connector with the
power on. Make sure to turn off the power before operation.
●
Installing in the following places may result in malfunction.
1. A dusty or steamy place.
2. A place generating corrosive gas.
3. A place directly receiving scattering water or oil.
4. A place suffered from heavy vibration to impact.
●
The product is not designed for outdoor use.
●
Do not use the sensor on transient state after power
on (approx.300ms).
●
Do not wire with the high voltage cable or the power line.
Failure to do this will cause malfunction by induction or damage.
●
The sensor performance or digital display values may depend on
the individual units or the condition if detected product.
●
Operate with in the rated range.
●
Don't bend the cable when the temperature of the cable or atmo-
sphere is below freezing.
●
Setting of sensing distance by potentiometer
1. Turn the potentiometer counter clockwise slowly until the output indicator
LED (orange) turns OFF.
●
Switching Light ON / Dark ON
When exporting this product to USA, it's necessary to follow laser regulation of
USA FDA.
This product has been already reported to CDRH (Center for Devices and Radio-
logical Health). For details, contact our customer service.
Precautions for using laser
You can select output polarity by the potentiometer SW as follows.
Light ON (L) : Output is ON when the sensor detects the reflected light.
Light OFF (D) : Output is ON when the sensor doesn't detect the reflected light.
This product is classified as Class 1 Laser Product by JIS C6802/IEC60825-1
Laser Safety Standard.
2. Turn the potentiometer clockwise slowly until both of the output indicator LED
(orange) and stable indicator LED (green) turn ON. Then, setting of sensing di-
stance is completed.
※
2 Output type have two sens. Adjusters and individual setting is possible.
※
Default setting is "Light ON"
This product cannot be used as a safety device
to protect human body.
Name of the parts and setup
Q2 sens Adjuster
(2 output type only)
Q1 sens Adjuster
Q1 Output indicator (orange)
Stable indicator (Green/Red)
Laser off indicator (off)
Q2 Output indicator (orange)
(2 output type only)
L/D Selector
OPTEX FA CO.,LTD.
TOF-L450
SERIES
・TOF-L450□□
・TOF-L450D□□
INSTRUCTION MANUAL
●
Thank you for purchasing TOF-L series. We hope you are satisfied
with its performance.
●
Please read this manual carefully and keep it for future reference.
Photoelectric Sensor
Dimensions
Input and output circuit diagram
NPN
type
PNP
type
M8 Connector pin No.
M12 connector pin No.
保護回路
路
回
主
負荷
路
回
主
負荷
路
回
主
保護回路
4
2
1
1
3
4
3
①・・・
DC10~30V
②・・・
External input (laser OFF)
③・・・
0V
④・・・
Output 1
①・・・
DC10~30V
②・・・
Output 2
③・・・
0V
④・・・
Output 1
⑤・・・
External input (laser OFF)
SPECIFICATIONS
Protection
Protection
Load
Load
0V
Blue
Gray External input
DC10~30V
Output 1
Brown
Black
White Output 2
Main circuit
(laser OFF)
Protection
Protection
Load
Load
0V
Blue
Gray
External input
DC10~30V
Output 1
Brown
Black
White Output 2
Main circuit
(laser OFF)
M8 4pin connector
28.25
4.8
Receiver
Emitter
2.1
44.4
9
16
Φ4.5 5 core 2m cable (2 output type
）
Φ4.5 4 core 2m cable (1 output type)
Φ4.5 M12 5 pin 300mm connector cable
39.2
3.1
2.6
7
6
2.8
32.8
1.25
17
Installation
保護回路
路
回
主
負荷
路
回
主
負荷
路
回
主
保護回路
4
2
1
1
3
4
3
①・・・
DC10~30V
②・・・
Output 2
③・・・
0V
④・・・
Output 1
1
2
4
3
5
IEC60825-1
：
2007
Horizontal →Vertical
Vertical → Horizontal
M8 connector can be turned from (to) straight
to (from) right angle though, movable angle ra-
nge is limited as the picture above. Please don't
turn it out of the angle range otherwise it could
be a cause of damage.
1 Output
2 Output
Diffused Reflection type
Output quantity
Type
1 Output
2 Output
TOF-L450C(N/P)
Connection
M8 connector
TOF-L450(N/P)
2m cable
TOF-L450M12(N/P)
M12 connector cable
TOF-L450D(N/P)
2m cable
TOF-L450DM12(N/P)
M12 connector cable
TOF-L450DC(N/P)
M8 connector
Sensing distance
* 1
Light source
Model
Red laser diode (wave length : 650nm, maximum output 64mW, pulse length 9ns, light projection period 16.67MHz
）
4.5m (white 90%)
φ
15mm / 4 m
Spot size
Beam divergence
±1.5°
（
±9 mrad
）
max
15% max
Laser class
CLASS 1 Laser product (IEC60825-1 / Laser Notice No.50)
Supply Voltage
DC10~30V
Including ripple (P-P)10%
Current Consumption
85mA max.
Response time
0.5ms
Hysteresis
External input
Operating mode
Light ON / Dark ON selectable by volume
Sensitivity adjustment
4 turn volume
Laser OFF
(NPN : Low active, PNP : High active)
Laser OFF
(NPN : Low active, PNP : High active)
Control output
NPN/PNP open collector DC30V, 100mA max
（
Residual 1.8V max
）
Number of cross talk prevention
Circuit Protection
2 Units max
Reverse polarity, Over current
Indicator
Output indicator (orange LED) /Stable indicator (Green LED)
Ambient Temp./ Humidity
-10
〜
50
℃
/35
〜
85%RH
Storage Temp./Humidity
Ambient
illuminance
-40
〜
70
℃
/35
〜
95%RH
Vibration resistance
Shock resistance
Protection category
IP67
Sun light
4,000lx max (at 1m)
3,000lx max (at 1m)
10~55Hz amplitude 1.5mm X
，
Y
，
Z each 2h
500m/s
2
X
，
Y
，
Z each 3 times
Incandescent Light
Material
Case : ABS / Lens : PMMA
-
Tightening torque: 0.5N・ｍ Max.
[ mm]
FDA Certification label
Spec of laser diode built in:
Wave length :
650nm,
Maximum output
7mW, Beam width angle 9 deg.
■
Cable,M12 type
■
M8 Connector type
Receiver
Emitter
9
23.85
53.8
0.55
1.5
7.85
11.7
15
31.3
20
17
9.3
2-R 2.1
2-R
2.1
R22.1
20°
Φ4.5 5 core 2m cable
（
2 output type
）
Φ4.5 4 core 2m cable
（
1 output type
）
Φ4.5 M12 5 pin 300mm connector cable
2-M3
10.45
39.2
4.1
31.3
1.29
2.8
19.2
2.8
31.3
12.65
M8 4pin connector
●With mounting bracket
●Without mounting bracket
Indicates a possible hazard that may result in death, serious
injury, WARNINGS or serious property damage if the product
is used without observing the stated instructions.
WARNING
UL Satisfaction Ratings
:10 - 30 V dc, Class 2, max. 100 mA
Input
:10 - 30 V dc, Class 2, max. 100 mA
Output
Output x1 model
:10 - 30 V dc, Class 2, max. 200 mA
Input
:10 - 30 V dc, Class 2, max. 100 mA
Output
Maximum surround air Tempe50
℃
Output x2 model
All Model
Resistive x1
Resistive x2
