■ NPN type
Instruction manual
Bundled goods in the box
Please confirm following goods bundled in the box.
・
%*6+/ƑƑƑƑ
・This instruction manual
● The light source of this product applies the visible light semiconductor laser. Do not
allow the laser beam to enter an eye, either directly or reflected from reflective object. If
the laser beam enters an eye, it may cause blindness.
● This product is not an explosion proof construction. Do not use the product under flam-
mable , explosive gas or liquid environment.
● Do not disassemble or modify the product since it is not designed to automatically stop
the laser emission when open. Disassembling or modifying at customer's end it may
cause personal injury, fire or electric shock.
●Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
● It is dangerous to wire or attach/remove the connector while the power is on. Make sure
to turn off the power before operation.
● Installing in the following places may result in malfunction:
1. A dusty or steamy place
2. A place generating corrosive gas
3. A place directly receiving scattering water or oil.
4. A place suffered from heavy vibration or impact.
● The product is not designed for outdoor use.
● Do not use the sensor in a transient state at power on (Approx. 2sec. Warm up period)
● Do not wire with the high voltage cable or the power lines. Failure to do this will cause
malfunction by induction or damage.
● Do not use the product in water.
● Operate within the rated range.
● Wipe off dirt on the emitting/receiving parts to maintain correct detection. Also, avoid
direct impact on the product.
Warning Mandatory Requirements
Warning Safety Precautions
Indicates a possible hazard that may result in death, serious
injury, WARNINGS or serious property damage if the product is
used without observing the stated instructions.
BGS-HL Series
BGS-HL05T □
BGS-HL25T □□
- Thank you for purchasing BGS-HL series. We hope you are satisfied with its performance.
- Please read this manual carefully and keep it for future reference.
High resolution BGS sensor
Dimensions
Connection diagram
■ PNP type
■ Pins configuration
( sensor side )
■ Cable type
■ M8 connector type
Display
ij
4.5 4core 2m Cable
Display
M8 4pin
Connector
Emitter axis
Emitter axis
؟9
%URZQ؟ٔ9
%ODFN
*UD\
%OXH
'&ؙع9
؟&RQWURO2XWSXW
؟([WHUQDO,QSXW
㻹
㼍㼕
㼚
㻌
㻯
㼕㼞
㼏㼡㼕
㼠
Specifications
Setup
Functions of components
●
6SHFL¿FDWLRQV
●
Part number legend
㻮㻳㻿㻙㻴㻸
㻌
䠻㻌䠻㻌
㼀
㻌䠻㻌䠻㻌
:RUNLQJGLVWDQFHقFPك
/DVHU&ODVV
&RQQHFWW\SH
ٴQRQH؟&DEOH
ٴ&ؙ؟0&RQQHFWRU
ٴQRQH؟&ODVV
ٴ ؟&ODVV
㻯㼛㼚㼠㼞㼛㼘㻌㼜㼍㼚㼑㼘
㻴㼛㼘㼑㼟㻌㼒㼛㼞㻌㼕㼚㼟㼠㼍㼘㼘㼍㼠㼕㼛㼚
㻔㻹㻟㻌㻖㻌㻞㻕
㻸㼑㼚㼟㻌㻔㻱㼙㼕㼠㼠㼑㼞㻛㻾㼑㼏㼑㼕㼢㼑㼞㻕
㻖 㼀㼕㼓㼔㼠㼑㼚㼕㼚㼓㻌㼠㼛㼞㼝㼡㼑㻌㼙㼡㼟㼠㻌㼎㼑
㻜㻚㻡㻺䞉㼙㻌㻹㼍㼤㻚
㻯㼍㼎㼘㼑㻌㻔㼙㼕㼚㼕㼙㼡㼙㻌㼎㼑㼚㼐㼕㼚㼓㻌㼞㼍㼐㼕㼡㼟㻌㻦㻌㻝㻜㼙㼙㻕
㻖 㻰㼛㼚㻓㼠㻌㼎㼑㼚㼐㻌㼠㼔㼑㻌㼏㼍㼎㼘㼑㻌㼛㼒㻌㼠㼔㼑㻌㼛㼡㼠㼘㼑㼠
㼜㼍㼞㼠㻌㼡㼜㻌㼠㼛㻌㻟㻜㼙㼙㻌㼒㼞㼛㼙㻌㼠㼔㼑㻌㼏㼍㼟㼑㻚
●
Control panel
● Changing mode
While it's "Setup mode" or "Extension mode", you can change the mode to "RUN mode"
by clicking "TEACH/RUN" button.
While it's "Extension mode", the LED "MANUAL" is lit.
●
Changing parameters
You can choose and adjust the parameters by clicking "+" and "-" buttons.
The mode will be changed to "RUN mode" by clicking "TEACH/RUN" button.
Teach function
㻿㻱㼀
䠉
䠇
䠉
䠇
㻯㼔㼍㼚㼓㼕㼚㼓
㼜㼍㼞㼍㼙㼑㼠㼑㼞
㻭㼐㼖㼡㼟㼠㼕㼚㼓㻌
㼜㼍㼞㼍㼙㼑㼠㼑㼞
・Screws
M3 × 15…2
[mm]
・Bracket
・ M8 connector type
%ODFN
%URZQ
:KLWH
%OXH
؟9
؟([WHUQDO,QSXW
؟&RQWURO2XWSXW
9
%URZQ؟ٔ9
'&ؙع9
%ODFN
*UD\
%OXH
㻹
㼍㼕
㼚
㻌
㻯
㼕㼞
㼏㼡㼕
㼠
㻻㼁㼀䚷䠖㻻㻺㻌㼣㼔㼑㼚㻌㼛㼡㼠㼜㼡㼠㻌㼕㼟㻌㻻㻺
㻹㻭㻺㼁㻭㻸䠖㻻㻺㻌㼣㼔㼑㼚㻌㻎㻱㼤㼠㼑㼚㼟㼕㼛㼚㻌㼙㼛㼐㼑㻎
㻸㻭㻿㻱㻾䚷䠖㻌㻻㻺㻌㼣㼔㼑㼚㻌㼘㼍㼟㼑㼞㻌㼕㼟㻌㼑㼙㼕㼠㼠㼑㼐
㻾㼁㻺㻌㼙㼛㼐㼑
㻿㼑㼠㼡㼜㻌㼙㼛㼐㼑
㻱㼤㼠㼑㼚㼟㼕㼛㼚㻌㼙㼛㼐㼑
㻯㼔㼍㼚㼓㼑㻌
㼠㼔㼞㼑㼟㼔㼛㼘㼐㻌
㼘㼑㼢㼑㼘㻌㼐㼕㼞㼑㼏㼠㼘㼥
㻼㼞㼑㼟㼟㻌㻞㻌㼟㼑㼏㼛㼚㼐㼟㻌
㼛㼞㻌㼙㼛㼞㼑
㼀㼑㼍㼏㼔㻌㼏㼡㼞㼞㼑㼚㼠㻌
㼜㼛㼟㼕㼠㼕㼛㼚
㻰㼕㼟㼜㼘㼍㼥㼟㻌㻎㻞㼜㼠㻎㻌
㼍㼚㼐㻌㼏㼡㼞㼞㼑㼚㼠㻌
㼜㼛㼟㼕㼠㼕㼛㼚㻌
㼍㼘㼠㼑㼞㼚㼍㼠㼑㼘㼥
㼃㼔㼑㼚㻌㼕㼠㻌㼕㼟㻌㻎㻞㼜㼠㻌㼠㼑㼍㼏㼔㼕㼚㼓㻌㼙㼛㼐㼑㻎
㻯㼘㼕㼏㼗
㻯㼘㼕㼏㼗
㻾㼁㻺㻌㼙㼛㼐㼑
㻯㼘㼕㼏㼗
Part
number
Cable type
BGS-HL05T
BGS-HL25T2
Connector type
BGS-HL05TC
BGS-HL25TC2
Sensing range
※
1
20 ~ 50mm
(Display: 0.00 ~ 30.00)
50 ~ 250mm
(Display: 0.0 ~ 200.0)
Light source
Red laser Diode (wave length 655nm)
390
μ
W
1mW
Laser
class
IEC/JIS
CLASS 1
CLASS 2
Spot size
※ 2
φ 0.8 mm
@ 50mm
φ 1 mm
@ 250mm
Repeat accuracy
10
μ
m
100
μ
m
※ 3
Sampling period
500
μ
s / 1000
μ
s / 2000
μ
s / 4000
μ
s / AUTO
Response time
1.5ms max. (1.5~7ms/default)
1.5ms max. (3~14ms/default)
Hysteresis
0 ~ 22.49 (default: 0.15）
0 ~ 149.9 (default: 1.0）
Display
7-segment 4-digit LED display
Indicator
Laser indicator: Green,
Output indicator: Orange, Mode indicator: Red
Control Output
NPN/PNP selectable
100mA max./DC24V (Residual voltage 1.8 V max.)
External Input
Laser OFF, Teaching, Sample Hold, One shot hold
Timer function
OFF/On delay/Off delay/One shot
1msec increment : 0 ~ 9999ms
Supply voltage
12 ~ 24VDC including 10% ripple
Current consumption
40mA max. / 24VDC excluding the current of Control Output
Protection circuit
Reverse connection protection, Over current protection
Protection category
IP67
Operating Temp./Humid.
-10
~
50
℃
/ 35 ~ 85% RH without freasing or condensation
Storage Temp./Humid.
-20 ~ 60
℃
/ 35 ~
85%/RH
Ambient illuminance
Incandescent lamp: 3,000 lx max.
Vibration resistence
10 ~ 55Hz, Double amplitude 1.5mm, X,Y,Z for 2 hours
Shock resistence
500m/s
2
( approx. 50G) X,Y,Z 3 times each
Material
Case: Aluminum, Front lens: PPSU, Display: PET
Weight
Cable type : Approx. 90g (including cable)
Connector type : Approx. 30g
The specifications are based on the condition unless otherwise designated: Ambient temperature: 23℃ , Sup-
ply voltage: 24VDC, Sampling period: 500
µ
s, Averaging: 512, Measuring distance: Center of the range, Testing
object: White ceramic
※ 1 When [Shift] in Extension mode is ON, the display shows 0000 at the Teaching point.
The range that the display can show is as follows.
BGS-HL05 -7.50 ~ 37.50
BGS-HL25 -50.0 ~ 250.5
When the distance exceeds this range in Sensing range, the display shows FFFF. Although, the sensor
works while the distance is in Sensing range. The display shows 9999 when the distance is out of range.
※ 2 Defined by light strength within 1/e
2
(13.5%) of spot center. There may be leak light at outside of the
specified spot size. The sensor may be affected when there is a highly reflective object at that leak light
area.
※ 3 Sampling period : 1000
μ
s
.
You can change threshold level directly by “+” and “-” buttons after clicking “TEACH/
RUN” button from “RUN mode”.
By pressing “TEACH/RUN” button for 2 seconds or more, it gets to “Teaching mode”. It
has 3 “Teaching mode” that you can choose one in “Setup mode”.
Please refer “Teaching mode” and “Setup mode” on next page.
Precautions for using laser
● Regulations in the USA
When exporting laser devices to the USA, the USA laser control, FDA
(Food and Drug Administration) is applied. This product has been already
reported to CDRH (Center for Devices and Radiological Health). For
details, contact our customer service.
MAX. OUTPUT 1mW
WAVELENGTH = 655nm
EN/IEC 60825-1:2007
Complies with 21 CFR
1040.10 and 1040.11
except for deviations
pursuant to laser notice
No.50, dated June 24, 2007
CLASS 2 LASER
PRODUCT
MAX. OUTPUT 390
μ
W
WAVELENGTH = 655nm
EN/IEC 60825-1:2007
Complies with 21 CFR
1040.10 and 1040.11
except for deviations
pursuant to laser notice
No.50, dated June 24, 2007
CLASS 1 LASER
PRODUCT
Complies with 21 CFR 1040.10 and 1040.11
except for deviations pursuant to
laser notice No.50, dated June 24, 2007
OPTEX FA CO.,LTD.
OFROM CO.,LTD.
91 Awata-cho Chudoji Shimogyo-ku Kyoto 600-8815 JAPAN
Place of manufacture :
Manufactured in
Ramco Innovations
www.optex-ramco.com
Got Questions? 1-800-280-6933
Need Technical Support or Help with a Tough Application? Contact the experts at Ramco today! Our email is [email protected]
