manualshive.com logo in svg

FASTLITE DAZZLER, Manual

Share
Download
FASTLITE DAZZLER Manual Download Page 76

chapter 7

Cabling tips

The laboratories where the Dazzler

TM

systems are used are often full of noisy signals which

may impair the proper operation of the system. This chapter provides tips on the layout of the
cables. These tips are also applicable to other equipment, like pockels cells, trigger generator,
etc. and have to be applied to the whole platform to control the interferences.

7.1

Basic principles

Reduce area between ground plane and cables.

Do that for both the noise producer and the sensitive piece of equipement. This will reduce
harmful emission from the noise source and reduce the received perturbations.

Typically, the noise sources are pockels cells high voltages switches. Victims are USB cables,
attached PC and Dazzler components. Trigger cables and trigger box, if low jitter is required,
are also affected.

7.1.1

Ground plane, layout & crossings

The top of the optical table (the mechanical reference) should be connected to earth for safety.
For EMI/EMC control this is not effective and the following tips may/have to be implemented.
The first step is to turn the mechanical reference into a good RF ground plane (RF electrical
reference). If the sheet is made of aluminum alloy, the surface may be not conductive due to
the aluminum oxide. Check this with an impedance meter. If made of two or more sheets,
these sheets shall be bonded together with copper or aluminum conductive tape

1

. The cables

have to be laid down to the ground plane or as close as possible to the conducting surface.

When a power cable has to cross a signal cable, it should do so at right angles and be kept as
far as possible from the signal cable.

This layout minimizes the coupling

2

between the cables. If you are using pockels cells with a

1

Ex: French Radiospares, Advance Tapes, AT 526 Conductive Copper Tape, 10MMX33M,Ref.: 542-5505.

2

Mutual inductance

70

Summary of Contents for DAZZLER





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands