FAST ComTec 7072T User Manual Download Page 4

Page: 4 / 20

Table of Figures

ComTec GmbH

Table of Figures

Figure 2.1: Front panel.................................................................................................................. 2-1

Figure 2.2: Gate/Start input schematic ......................................................................................... 2-2

Figure 2.3: FAST-NIM input schematic......................................................................................... 2-3

Figure 2.4: MONITOR output signals............................................................................................ 2-3

Figure 2.5: Rear panel .................................................................................................................. 2-5

Figure 2.6: ADC port connectors .................................................................................................. 2-5

Figure 4.1: General ADC Signal Timing........................................................................................ 4-3

Figure 4.2: PHA, typical noise spectrum....................................................................................... 4-4

Figure 4.3: ADC, typical differential linearity plot .......................................................................... 4-5

Figure 4.4: TDC, typical noise spectrum (50ns range) ................................................................. 4-6

Figure 4.5: TDC, typical differential linearity plot (50ns range)..................................................... 4-6

Summary of Contents for 7072T




















