INSTALLATION
Unpacking
Remove the DVP1010 unit from the shipping
container and examine it for any signs of shipping
damage or missing items (check inventory list below).
All shipping materials should be saved if the unit is to
be moved or returned for service. Shipping unit back
to Faroudja for service not in the original box may
result in voiding warranty or additional cost.
Placement
The processor can be either placed on a table or rack
mounted. A rack mounting installation kit is included.
Securely mount the side rack brackets with the
screws that are provided with the kit.
Ventilation
The unit uses convection to cool. A fan is not
needed. As hot air raises out of the top vent, cool air
is drawn in from the bottom and side.
These vents
must not be blocked
. When rack mounted, a
minimum of 1.75” (1 rack unit height) of free space is
required above and below the unit to allow for proper
cooling. A forced air fan should be added to the rack
installation if power amps are located in the same air
space. Do not install unit above power amps.
Connections
Because of the high performance of the DVP1010
unit it is very important to use the highest quality
cables possible, for both input and output signals.
To avoid AC ground loop problems, the source
equipment, DVP1010 unit and projector should all be
running on the same grounded AC power line (one
rated for the power requirements).
1.
S-Video input (4-pin DIN) for sources such as
DVDs, Satellite systems, S-VHS tape decks
(when using S-VHS tapes only),
Hi-8 tape decks.
2.
Composite video input (BNC) for sources such
as Laserdisc players, cable TV, VHS tape
decks, 8mm tape decks.
3.
YPrPb/RGBs Input (BNC): 480i and HDTV
scan rates are sent to the internal processor
and then output at the selected scan rate. If
the output is set to analog RGBHV or digital
DVI, the unit will automatically transcode the
YPrPb HDTV to RGBHV.
Note on DVDs:
For proper aspect ratio and to
insure the highest quality image from the DVD
player, be sure to set the DVD screen shape
to 16:9 in the DVD player's Setup menu. See
the DVD player's owner's manual for details.
4.
High scan rate input (D15F) for sources such
as HDTV signals or computers are passed
through to the projector. The signal is sent to
the outputs in the same format as the input
unless Transcoding is selected. YPrPb from
HDTV sources can be transcoded to RGBHV,
as well. Use a BNC to D15 breakout cable if
necessary. The Green, Red, Blue BNCs are
used for YPrPb.
5.
D15F connector output for use with computer
monitors or to a second display device. Use
only short cable runs. This output can be used
at the same time as the BNC outputs.
6.
DVI Input. The DVI Input will automatically
process
480i,
480P,720P and 1080i signals.
Computer rates are passed through to the DVI
output if any of the pass-through inputs are
selected. The DVP1010 will not convert a
computer DVI output to the analog output.
7.
DVI Output: Digital output interface for
compatible displays. All processed analog
and digital inputs are output to this connector
as well as computer scan rates when the
pass-through input is selected. Maximum
cable length is 50ft with a high quality DVI
cable. For longer lengths a distribution system
or fiber optic system must be used.
8.
BNC connectors for main output with RGBHV
or YPrPb signals to display devices. Cable
runs up to 100ft are okay if good quality cables
are used. For YPrPb outputs use:
Red =
Pr
Green =
Y
Blue =
Pb
RGBHV is recommended.
2
INSTALLATION
Inventory
1-DVP1010 Unit
1- Batteries
1-Owner’s Manual
1- Warranty Card
1- Power Cord
1
2
4
5
6
7
8
3
9 10
12
11
13
