d) Press the button of the
GR-9200
on
which you wish to learn, watch the LED
which initially will stay on and within
5
seconds…
e) Press and keep pressed the button of the
original remote control to be learned,
releasing it when the LED goes off (two
short flashes shortly after will confirm
memorization).
f) To memorize more commands repeat
the procedure from d).
N.B.:
• If the LED emits two long flashes there has
been a problem and you have to repeat
the procedure from d).
• Exit from the learning function is automa-
tic after approx.
8
seconds of the last ope-
ration (or its interruption) and is signaled
by a long flash of the LED. To enter the
learning function again repeat from b).
• To learn a new command on a button that
has already been memorized it is neces-
sary to first clear the memory (4.2)
4.2
) Cancellation procedures.
Cancellation procedures are used when
wanting to replace a learned command with
another learned command or restore a pre-
programmed command (See NOTE above).
4.2.A
) Cancellation of only one button.
a) Press and release the «
» button.
b) Enter the code «
6 6 6 6
».
c) Press the button to be cleared and watch
the LED that will confirm cancellation
with 2 short flashes.
d) To cancel more commands repeat from
a).
N.B.: Exit from cancellation mode is auto-
matic after approx.
8
seconds of the last
operation.
4.2.B
) Total cancellation (on all buttons of
both memory banks).
a) Press and release the «
» button.
b) Enter the code «
7 7 7 7
» and watch the
LED that will confirm cancellation with
two short flashes.
5)
“WHAT TO DO IF…”
- After the batteries have been inserted, the
LED will not flash when pressing the
«
» button?
Check that the batteries have been inserted
with correct polarity.
- The automatic search was unsuccessful?
Repeat the operation and observe the
LED
After a while you will notice that the LED
emits 5 short flashes indicating the end of a
search cycle. Keep the search button
pressed…if your machine still does not
respond and the LED again emits 5 short fla-
shes, abandon this procedure and try inser-
ting manually, one by one, following
the procedures in the previous chap-
ters, all the codes listed in the tables
(Tab. A for TVs,Tab. C. for VCRs).
- You have some difficulties with the learning
function?
Try repositioning the two remote controls
changing the distance and/or alignment.
- After a while the operation of the remote
control becomes erratic?
Make a note of the codes memorized (see
also para.
3
) and quickly change the batteries.
If no change, press (for example with the tip
of a pencil or non sharp object) the internal
reset button.
Take notice: after pressing the RESET
button it is necessary to enter again all the
required codes.
CODE
?
CODE
?
CODE
?
4
BLAUPUNKT
1001 - 1002
1003 - 1005
1006 - 1007
1008 - 1012
1014 - 1035
1037
TAB. A:
CODES OF TV
GRUNDIG
1001 - 1002
1003 - 1004
1009 - 1013
1034 - 1037
MINERVA
1001 - 1002
1003 - 1004
1034
SIEMENS
1001 - 1002
1003 - 1005
1007 - 1008
1010 - 1011
1015
LOEWE
1016 - 1017
1018 - 1019
1020 - 1021
1022
METZ
1018 - 1023
1024 - 1025
1026 - 1028
1029 - 1030
1031 - 1032
N.E. GR 9200 (GB) 13-07-2000 11:58 Pagina 4
