FarmTek Growers Supply HydroCycle 4" Pro NFT Manual Download

Page: 3 / 31

Revision date: 01.14.21

112525

110725

Air Pump

109260 Air Stone

110722

Utility Pump

111046

1/4" White Polyethylene Tubing

110091 Clear Vinyl Tubing

111698 Ratchet Clamp

WR1095

Tape

Plastic Pipe & Tube Cutter

116215 (4)

End Cap w/ Outlet

116214 (4)

End Cap No Outlet

Important Information

PICTORIAL GUIDE

The following graphics and photos will help identify the different parts of the hydroponic system. (Some

parts may not be shown.) To prevent mixing of fittings, select only those that are needed for each procedure.

Keep all fittings in the shipping bags until they are needed.

10015106

Short Tee Fitting (12)

100442 (1)

Nut Setter

FA4470B (10)

Tek Screw

WF6990

PVC Cement and

113372 Purple Primer

PVC PRIMER & CEMENT

Follow all directions printed on pvc primer and

cement containers.

Purple color of primer

does not fade

! Use caution during application

to reduce spills and over application at joints.

Prime all joints before assembly.

WF6504A

3/4" Black Hose

Summary of Contents for Growers Supply HydroCycle 4" Pro NFT
































Search results

Summary of Contents for Growers Supply HydroCycle 4" Pro NFT

Reviews:

Related manuals for Growers Supply HydroCycle 4" Pro NFT

Brands by name

Popular brands

FarmTek Growers Supply HydroCycle 4" Pro NFT, Manual

Search results

Summary of Contents for Growers Supply HydroCycle 4" Pro NFT

Reviews:

Related manuals for Growers Supply HydroCycle 4" Pro NFT

Brands by name

Popular brands