FarmTek FodderPro 2.0 Full Feed System-Wall Mount 111628W Manual Download

Page: 2 / 53

111628W

Revision date: 09.25.18

READ THIS DOCUMENT BEFORE YOU BEGIN

Thank you for purchasing the 111628W FodderPro 2.0 Full Feed System – Wall Mount. When properly assembled and maintained, this product will provide

years of reliable service. This guide includes information needed to safely assemble and maintain the system. Read these instructions

before

you begin.

Important Information

REQUIRED TOOLS

The following list identifies the main tools needed to

assemble the fodder system.

Additional tools and

supports may be needed.

• Tape measure and marker
• Variable speed drill (cordless with extra batteries

works best) and drill bit set with a 9/32" & 7/16" bit.

•  Small hammer and gloves
•  PVC Tube Cutting Tool
•  Level 4' (or longer)
•  Wrench set or adjustable wrenches
•  Socket Set with Ratchet
•  Straight Screw Driver
•  1-3/8" hole saw bit for the drain manifold
•  Adjustable pliers
•  5/8" nut driver (or 5/8" socket)
•  Ladder or work platform to work at the height of

the fodder system frame.

ASSEMBLY PROCEDURE

This manual describes how to assemble a single

111628W FodderPro 2.0 Full Feed System – Wall

Mount.

The steps outlining the assembly process

are as follows:
1. Unpack the contents of the shipment and

place where you can easily inventory the

parts. Refer to the Bill of Materials/Spec

Sheets.

2. Verify that all parts listed on the Bill of

Materials/Spec Sheets are present. If anything

is missing or you have questions, consult

the Pictorial Parts Guide and all diagrams for

clarification, or contact Customer Service.

3. Read these instructions and all additional

documentation included with the shipment

before

you begin.

4. Gather the required tools.
5. For best results, assemble the components

in the order they are presented in these

instructions.

SAFETY PRECAUTIONS

•  Wear eye protection.
•  Wear gloves when handling metal tubes.
•  Use a portable GFCI (Ground Fault Circuit

Interrupter) when working with electric power tools

and cords.

QUICK START GUIDE

For a quick overview of this product and its

components, consult the Quick Start Guide at the

back of these instructions.

ATTENTION:

This manual describes how to

assemble one 111628W FodderPro 2.0 Full Feed

System – Wall Mount. If you are connecting this

system to another, minor adjustments must be

made to some of the procedures that follow.

Consult the diagram on Page 4 for additional

details regarding multiple systems.

ELECTRICAL WARNING

Fodder frame is metal and will conduct electricity!

Exercise caution if working around or on the

frame with electric power tools.

Use cordless,

battery-power tools.

CONSULT THE SERVICES OF A QUALIFIED

ELECTRICAL TECHNICIAN WHEN INSTALLING

ANY PUMPS, ARTIFICIAL LIGHTING,

OR OTHER ELECTRICALLY POWERED

ACCESSORIES.

OPEN SYSTEM

The 111628W FodderPro 2.0 Full Feed System

– Wall Mount is an open system, which means

that the water is not recycled for use

in the

fodder system

. Unlike a closed system where

the water is stored in a reservoir and recycled,

the open system requires a water source

and a drain to accept the unused water. The

unused water can be recycled for use in other

applications such as watering other plants;

however,

to promote healthy fodder growth

it is not recommended for reuse in the fodder

system.

WARNING:

This is not a free-standing

frame! You must secure the frame to the wall

using the appropriate fasteners and supplied

brackets. Contact the services of a qualified

contractor for assistance if needed, or call your

sales representative for additional fastener

information and to purchase fasteners.

DO NOT USE THE FODDER SYSTEM WHEN

THE FRAME HAS NOT BEEN PROPERLY

SECURED TO THE WALL!

NEVER CLIMB ON THE FODDER FRAME!

Summary of Contents for FodderPro 2.0 Full Feed System-Wall Mount 111628W






















































Search results

Summary of Contents for FodderPro 2.0 Full Feed System-Wall Mount 111628W

Reviews:

Related manuals for FodderPro 2.0 Full Feed System-Wall Mount 111628W

Brands by name

Popular brands

FarmTek FodderPro 2.0 Full Feed System-Wall Mount 111628W, Manual

Search results

Summary of Contents for FodderPro 2.0 Full Feed System-Wall Mount 111628W

Reviews:

Related manuals for FodderPro 2.0 Full Feed System-Wall Mount 111628W

Brands by name

Popular brands