FARMSCAN 30007000-7999 Manual Download Page 19

Page: 19 / 21

WWW.FARMSCANAG.COM

AM-JACKAL-B / OCT 2018

GPS/SERIAL

The GPS/Serial menu allows you to confirm
that the GPS connected to the Jackal is
function correctly.

By pressing the

SETUP

, confirm the correct

strings and Baud rate.

EDIT

GPS settings re-run the wizard by

pressing

SETUP

from the front screen.

Your existing settings will not be lost during the wizard re-run.

ABOUT JACKAL

Displays the Firmware version that’s installed on the Jackal.

This screen also allows you to

UNLOCK

your Jackal to further functionality.

Please contact Farmscan Ag should you wish to purchase an unlock code.

DIAGNOSTICS

This screen provides the following information:

•

Voltage

Displays a live input voltage to the Jackal.

•

Current

Displays live Current draw on the Jackal.

•

Input “x”

When inputs are enabled, they will also

be displayed for easy diagnostics.

FACTORY RESET

WARNING

This screen allows you to return the Jackal to factory defaults.

All values will be lost after pressing

RESET.

Power cycle the Jackal to confirm all settings are reset.

Summary of Contents for 30007000-7999






















Search results

Summary of Contents for 30007000-7999

Reviews:

Related manuals for 30007000-7999

Brands by name

Popular brands

FARMSCAN 30007000-7999, Manual

Search results

Summary of Contents for 30007000-7999

Reviews:

Related manuals for 30007000-7999

Brands by name

Popular brands