Farmet FALCON 3 Operating Manual Download

Page: 24 / 99

Manual

FALCON 3 | 4 | 6 | 8

│

6.6.

PROPER CONNECTION TO THE TRACTOR

For proper connection, the following facts must be observed:

Outlet hose

Do not connect the free drain hose to the tractor distributor! (pressure in the reverse branch would thus
be increased)

Large quick coupling on the free drain must not be changed for the smaller diameter.

Oil returning through the outlet pipe must not be throttled anywhere

Maximum allowed pressure value in the free drain hose is 5 bar, higher pressure pushes the shaft seal
out, which causes damage to the hydraulic motor fan

Pressure hose

Connect the pressure hose to the circuit giving priority to the oil supply

Picture. 6 – Position of quick couplings in the tractor

6.6.1

Connecting the free drain

hose

Connect the outlet hose (outer

⌀

27 mm) with the large quick coupling to the free drain to the tractor tank.

In case that there is no free drain to the tank attached to the tractor as standard, please contact the tractor

manufacturer (dealer) for information regarding the possibilities of a free drain end piece.

Picture 7 – Outlet hose connection

Free drain to the

tractor tank must

be all time

connected, even if

fan is not working

Free drain to the tank

Tractor

distributor

Summary of Contents for FALCON 3




































































































Search results

Summary of Contents for FALCON 3

Reviews:

Related manuals for FALCON 3

Brands by name

Popular brands

Farmet FALCON 3, Operating Manual

Search results

Summary of Contents for FALCON 3

Reviews:

Related manuals for FALCON 3

Brands by name

Popular brands