Farmet FALCON 3 Operating Manual Download

Page: 23 / 99

Manual

FALCON 3 | 4 | 6 | 8

│

6.5.

CONNECTING THE HYDRAULIC MOTOR OF THE FAN

6.5.1

Description of the function

The hydraulic fan is powered directly from the tractor´s hydraulic system.

For proper operation, the hydraulic pump of the tractor must supply sufficient amount of oil so that the

fan revolutions are not affected by decreased number of revolutions of the tractor engine or by another hydraulic
circle being switched on.

The fan revolutions are set by regulating the oil flow rate. To change the fan revolutions, the tractor must

be equipped with regulation of the oil flow rate.

Picture. 5 – Hydraulic drive

Tab. 5

Rotary hydraulic

motor

Capacity (cm

/rev.)

Minimum revolutions of the small fan (rpm)

1000

Maximum revolutions of the small fan (rpm)

6000

Minimum revolutions of the big fan (rpm)

1000

Maximum revolutions of the big fan (rpm)

3000

Pressure oil - „P“

Minimum pressure in the “PRESSURE HOSE” (bar)

130

Maximum flow rate in the “PRESSURE HOSE”
(l/min.)

Outlet - „T“

Maximum pressure in the “PRESSURE HOSE” (bar)

Hydraulic motor

Fan

Pressure hose

Free drain to the

tractor tank must

be all time

connected, even if

fan is not working

Tank - „T“ (ISO 20)

Pressure - „P“ (ISO 12,5)

Measuring point of

pressure

in the free drain

hose

Summary of Contents for FALCON 3




































































































Search results

Summary of Contents for FALCON 3

Reviews:

Related manuals for FALCON 3

Brands by name

Popular brands

Farmet FALCON 3, Operating Manual

Search results

Summary of Contents for FALCON 3

Reviews:

Related manuals for FALCON 3

Brands by name

Popular brands