Farmet 2021/0625 Operating Instruction Download

Page: 44 / 102

Steps for setting the tramline rhythm correctly

Necessary information for calculating the rhythm of tramlines.

1. Seeder grip
2. Sprayer grip

We will perform calculation.

Result of the calculation =

Sprayer grip

Seeder grip

Possibilities of creating tramlines

1. Even results

– Even tramline rhythms (15.2.1)

2. Odd result

– Odd tramline rhythms (15.2.2)

3. Decimal results

– Special tramline rhythms (15.2.3)

Types of valves placement on the machine

TYPE A

One valve on each side of the machine.

TYPE B

One valve on one side of the machine.

TYPE C

Two valves on one side of the machine.

TYPE D

One valve on one side of the machine and two
valves on the other side of the machine.

TYPE E

Two valves on each side of the machine and
each side of the machine create a complete rail
line for the entire sprayer (2 tracks).

Summary of Contents for 2021/0625







































































































Search results

Summary of Contents for 2021/0625

Reviews:

Related manuals for 2021/0625

Brands by name

Popular brands

Farmet 2021/0625, Operating Instruction

Search results

Summary of Contents for 2021/0625

Reviews:

Related manuals for 2021/0625

Brands by name

Popular brands