Farmet 2021/0625 Operating Instruction Download

Page: 11 / 102

General instructions for use

(x)

The machine is manufactured in accordance with the latest state of technology and approved safety

regulations. Even that, there is a risk of injury to the user or third parties or damage to the machine or other
property damage.

(xx)

Use the machine only in harmless condition, in accordance with its intended use, with knowledge, with

knowledge of possible dangers and in compliance with the safety instructions in these operating instructions.

The manufacturer is not

responsible for damage caused by using the machine in violation of the machine’s

limit parameters and the instructions for using the machine. The risk is born by user.

Immediately remove defects, that can negatively effect safety risk.

3. The machine may be operated by a person authorized by the operator under the following conditions:

Must have a valid driving license of the relevant category.

They must be demonstrably acquainted with the safety regulations for working with the machine.

He must be familiar with the machine instructions and the machine operator.

They must know the meaning of the safety signs placed on the machine. Respecting them is important for
safe and reliable operation of the machine.

4. Maintenance and service repairs on the machine may only be performed by a person:

Authorized by the operator.

Demonstrably aguainted with the safety regulations for working with the machine.

When repairing a machine attached to tractor has to have the right category of driver license.

5. The operator of the machine must be sure of other persons safety when working with the machine or

transporting the machine.

6. When transporting the machine or working on the field the machine operator have to control the machine

from inside the cabin.

WARNING

– This warning sign must be in the immediate danger of a dangerous situation,

ending with serious injury or death.

ATTENTION

– This warning sign alerts you to a situation that could result in minor or minor

injury. It also alerts you to dangerous actions associated with activities that could damage
the machine.

NOTICE

– This warning sign indicates a technical recommendation.

RECOMMENDATION .

PRESS.

Summary of Contents for 2021/0625







































































































Search results

Summary of Contents for 2021/0625

Reviews:

Related manuals for 2021/0625

Brands by name

Popular brands

Farmet 2021/0625, Operating Instruction

Search results

Summary of Contents for 2021/0625

Reviews:

Related manuals for 2021/0625

Brands by name

Popular brands