manualshive.com logo in svg

Farm King Model 1050, Operator And Parts Manual

Share
Download
Farm King Model 1050 Operator And Parts Manual Download Page 92

90

Maintenance - 10" Backsaver Auger

Lubricate the following grease locations EVERY 50

HOURS:

NOTE: The PTO shaft is equipped with extended life

bearings. Do not over-grease.

Figure 145

Apply two - three pumps of grease to the cross and

bearings (Item 1) 

[Figure 145]

 on the PTO driveline.

Figure 146

Apply two pumps of grease to the guard bushings

(Item 1) 

[Figure 146]

.

Apply eight - ten pumps of grease to the telescoping

member (Item 2) 

[Figure 146]

.

Figure 147

Apply 1-2 pumps of grease to the universal joint (Item

1) 

[Figure 147]

 on the hopper auger drive shaft.

Figure 148

Apply 1-2 pumps of grease to the intake drive shaft

side (Item 1) 

[Figure 148]

.

B-0002

1

1

2-3

B-0002

1

1

2

2

1

8-10

2

B-0732

1

1-2

B-0712

1

1-2

Summary of Contents for Model 1050















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands