manualshive.com logo in svg

Farm King Model 1050, Operator And Parts Manual

Share
Download
Farm King Model 1050 Operator And Parts Manual Download Page 57

55

Assembly - 10" Backsaver Auger

Jack Installation

Figure 96

Align and install the jack (Item 1) 

[Figure 96]

 onto the

hitch (hopper side).

PTO Driveline Installation

Figure 97

Push back on the collar (Item 1) 

[Figure 97]

 and install

the shaft into the gearbox until the collar slides

forward, locking the shaft in the gearbox. Place the

PTO holder chain around the PTO driveline and hook

chain back to itself.

Hand Winch And Cable Installation

Figure 98

Install the hand winch mounting bracket (Item 1)

[Figure 98]

 on the opposite side of the hopper.

Install the pin (Item 2) and retaining clip (Item 3)

[Figure 98]

 to secure the hand winch mounting

bracket to the input box.

Figure 99

Align the hand winch (Item 1) 

[Figure 99]

 with the

three mounting slots on the hand winch mounting

bracket.

Install one 7/16” flat washer onto three 3/8” x 1” (Gr.

5) bolts (Item 2) 

[Figure 99]

. Install the three bolts and

flat washers down through the winch and mounting

B-0728

1

B-0767

1

B-0716

1

2

3

B-0717

1

2

Summary of Contents for Model 1050















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands