manualshive.com logo in svg

Farm King Model 1050, Operator And Parts Manual

Share
Download
Farm King Model 1050 Operator And Parts Manual Download Page 54

52

Assembly - 10" Backsaver Auger

Hopper Assembly And Installation

NOTE: The following images may not show your exact

hopper components as they appear but the

procedure is correct.

Figure 85

Place the rubber edge (Item 1) 

[Figure 85]

 inside the

outer flange of the hopper.

Figure 86

Align the end of the rubber edge with the two holes at

the back of the hopper. Install two 1/4” x 1” bolts

(Item 1) 

[Figure 86]

 through the hopper and rubber

edge. Install a 1/4” lock nut on each bolt.
Align one long rubber reinforcement (Item 2) and one

short rubber reinforcement (Item 3) 

[Figure 86]

 with

holes in the rubber edge and outer hopper flange (both

sides). Install 1/4” x 1” bolts through the hopper,

rubber edge and rubber reinforcements (install bolts

from the outside of the hopper flange). Install a 1/4”

lock nut on each bolt. Do not tighten bolts and lock

nuts at this time.

Figure 87

Align the two-hole rubber reinforcement (Item 1)

[Figure 87]

 with holes in the rubber edge and outer

hopper flange. Install two 1/4” x 1” bolts through the

hopper, rubber edge and rubber reinforcement (install

bolts from the outside of the hopper flange). Install a

1/4” lock nut on each bolt. Do not tighten bolts and

lock nuts at this time.

NOTE: When tightening the rubber edge bolts and lock

nuts, tighten until the lock nut contacts the

rubber reinforcements. Do not over tighten and

cause the rubber reinforcements to become

wavy.

Tighten all bolts and lock nuts to secure the rubber

edge to the hopper.

B-0448

1

B-0449

2

1

3

B-0451

1

Summary of Contents for Model 1050















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands