Farm King Model 1050 Operator And Parts Manual Download Page 28

Page: 28 / 174

Assembly - 10" Backsaver Auger

BASE GROUP

Undercarriage Assembly

Assemble the undercarriage on a flat level surface.

Figure 4

Install a strap (Item 1) around the center of the axle

(Item 2)

[Figure 4]

Connect the strap to an approved lifting device.
Raise and move the axle to the assembly area.
Lower the axle to the ground and remove strap.

Figure 5

Align the hub (Item 1)

[Figure 5]

with the axle.

Install the four 1/2” x 1-3/4” bolts (Item 2)

[Figure 5]

and 1/2” lock nuts. Tighten bolts and nuts.

Install a strap around the center of the right

undercarriage arm.
Connect the strap to an approved lifting device.
Raise and move the left undercarriage arm towards

the axle.

•

DO NOT permit bystanders to be in the work area

when unloading and assembling the auger

components.

•

DO NOT work under suspended parts.

•

Keep away from moving parts.

•

Always use lifting devices / vehicles, chains or

straps of adequate size and strength when

unloading and assembling the auger components.

AVOID INJURY OR DEATH

Keep fingers and hands out of pinch points when

assembling the equipment.

B-0583

B-0586

Summary of Contents for Model 1050















































































































































































Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands

Farm King Model 1050, Operator And Parts Manual

Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands